Stock Photo
See pictures for an example of what youwill receive.
PLEASE NOTE: You will receive ONE (1) of the remotes pictured - all have the same circuit boards and will program the same
Logo will vary: May be blank, DEI, Hornet, Sidewinder, Python, Rattler, Your Valet, or Viper - all are produced by Directed Electronics and will program the same.
One (1)
Aftermarket Security Installed Systemremotekeyless entry fob alarm controller
Transmitter control clicker keyfob controllerreplacement
DEI– Directed Electronics – VIPER- Python – Auto-Mate
– Rattler – SideWinder –Hornet – Merlin – Avital - Ungo
FCC ID#: EZSDEI471
Alternate Spelling: EZSDE1471
LED LIGHT: Green
Buttons: 2; I,II
Frequency: 433-434 MHz
Battery: 1; GP23A
See Item Specifications for more details
Compatible With the following Aftermarket installed security systems:
Automate
6
7
10
25
35
410
425
435
52
53
552
553
Avital
2100
2200
2300
3100
3200
3300
4000
4100
4200
4300
4400
Maxx2
Maxx3
Hornet
533 T
554 T
740 T
742 T
851 T
Python
400 HP
440 HP
450 ESP
460 HP
500 HP
625 HF
650 ESP
660 XP
700
900
1000 HF
PC 1000 HF
1200 XP
1400 XP
1500 HF
1600 XP
2000 HF
3000 HF
3000 ESP
Sidewinder
3000 HF
3000 ESP
3200 HS
3300 HS
3500 ESP
4500 HF
5000 HF
5000 ESP
5500 XS
6000 HF
6000 ESP
6500 HF
6500 ESP
7000 HF
7000 ESP
PC 7000 SHF
Rattler
100
110 D
200
210 D
250
259 R
300
310 D
359 R
369 D
Valet
450 R
519 H
551 R
552 T
562 T
561 R
712 T
716 T
Merlin
2000
Ungo
K10
K20
RK1
RS10
S100
S400
S660
S670
SR1000
SR5000
SR6000
Viper
100 HF (ESP)
130 HV
150 ESP
160 XV
210 HV
211 HV
300 HF
PC 300 HF (ESP)
300+ HF
330 V
350 HV
500 HF
Viper Continued…
PC 500 HF (ESP)
550 HF
550 HF (ESP)
560 XV
571 XV
600 HF
PC 600 HF (ESP)
650 XV
671 XV
700 ESP
771 XV
PC 800 SHF
Viper Continued…
800 SHF ESP
850 XV
1000
1002
3000
3002
5000
5002
7900
Programming Instructions:
The vehicle’s system can store up to 4 transmitters (remotes) into memory. Use the following programming routine to add transmitters to the vehicle’s security system or to change button assignments if desired.
In order to enter Learn Routine, the Valet/Program push button must be plugged into the main brain's Blue 2 Pin Port (Look for a small black push button located under the drivers dash or drivers kick panel somewhere).
The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to remember whenever programming this unit.
1) Open a door and make sure the dome light is on.
2) Turn the ignition on to the RUN position or you may also start car.
3) Within 10 seconds, press and release the Valet/Program switch the number of times that corresponds to the desired channel (listed below). Once you have selected the channel, press the switch once more and HOLD it. The LED will flash and then the horn will chirp (if connected) to confirm the selected channel. Do not release the Valet/Program switch.
4) You can advance from programming one channel to another by releasing the Valet/Programming switch and tapping it to advance channels and then HOLDING it. For instance; you have programmed Channel 1 and you want to program Channel 2. Release the Valet/Program switch. Press it one time and release it to advance from Channel 1 to Channel 2. Now, press and HOLD the Valet/Program switch. The LED will flash 2 times and the horn will chirp twice (if connected). As before, do not release.
5) If you want to program Channel 3 after programming Channel 1, release the Valet/Program switch, press it twice and release it to advance to Channel 3. Then press it once more and HOLD it. The horn will chirp 3 times (if connected) and the LED will flash 3 times to confirm it is ready to receive the code from the transmitter.
6) Once the code(s) are learned, the Valet/Program push button can be released.
7) Programming mode will be exited if one of the following actions occurs:
a. Ignition key is turned to the OFF position
b. Valet/Program switch is pressed too many times.
c. More than 15 seconds elapses between programming steps.
If you're notsure your vehicle can use thisremote, please ask questions or contact your local dealer first.
Yourvehicle will be installed with one of the following keyless entry systems:
Theabove information can change which remote you need
for your installed remote keyless system.
