Front Outer and Inner Tie Rod End Links Kit fit for 2017-2022 Honda CR-V GAS For Sale - New and Used

• 1 x Front Outer Tie Rod End - Driver Side - ES801496
• 1 x Front Outer Tie Rod End - Passenger Side - ES801495
• 2 x Front Inner Tie Rod Ends - Driver and Passenger Side - EV801486
• 2 x Tie Rod Boots + Bellows - 819515

• Spectrum Analyzing
• Salt Spraying Testing
• Three-coordinate Measuring
• Magnetic Flaw Detection
• Rubber Oxidation Testing
• Hardness Testing
• Pull-out Force Testing
• Endurance Testing

• Replacement for 2017-2022 Honda CR-V (GAS)

High strength patented multi-lip locking boot and Labor Saver hardware included for quick easy install. Easy-snap locking pin securely locks the ball joint.

Thread lock is pre-applied on inner tie rods, removing the need of applying it and reducing the time of installing the product.

Tie rods designed with longer wrench flats that provide a larger area for using a wrench which eases installation.

Pre-greased ball joint with Grease fitting allowing lubricant to flush contaminants and can extend service life.

When the Steering Tie Rod End become excessively worn, it will make wheel shimmy, which may cause vibrations felt in the wheel.The intensity of the vibrations will increase as you step on the accelerator pedal to go faster.

If Steering Tie Rod End develop excessive play or looseness, this can cause them to knock during takeoff, or when the vehicle is traveling over rough terrain. The clunking sound will continuously get louder as the component wears or until it eventually breaks.

Excessively worn Steering Tie Rod End can cause the vehicle’s steering alignment to shift, which may cause the steering to pull to the left or right when traveling down the road.

• All Listing
• Home
• Hot Listing
• Contect Us
• Control Arm
• BALL JOINT
• TIE ROD END
• BUSHING
• Stabilizer Bar Link
• Steering Idler Arm

• Package Includes:
  • 1 x Front Outer Tie Rod End - Driver Side - ES801496
  • 1 x Front Outer Tie Rod End - Passenger Side - ES801495
  • 2 x Front Inner Tie Rod Ends - Driver and Passenger Side - EV801486
  • 2 x Tie Rod Boots + Bellows - 819515
  • Spectrum Analyzing
  • Salt Spraying Testing
  • Three-coordinate Measuring
  • Magnetic Flaw Detection
  • Rubber Oxidation Testing
  • Hardness Testing
  • Pull-out Force Testing
  • Endurance Testing
  Fitment:
  • Replacement for 2017-2022 Honda CR-V (GAS)
  Qualified Product

  High strength patented multi-lip locking boot and Labor Saver hardware included for quick easy install. Easy-snap locking pin securely locks the ball joint.

  Pre-locked Thread

  Thread lock is pre-applied on inner tie rods, removing the need of applying it and reducing the time of installing the product.

  Longer Wrench Flat

  Tie rods designed with longer wrench flats that provide a larger area for using a wrench which eases installation.

  Greaseable socket

  Pre-greased ball joint with Grease fitting allowing lubricant to flush contaminants and can extend service life.

  Steering Tie Rod End should be checked and replaced when you encounter the following problems:
  Steering Wheel Vibrations

  When the Steering Tie Rod End become excessively worn, it will make wheel shimmy, which may cause vibrations felt in the wheel.The intensity of the vibrations will increase as you step on the accelerator pedal to go faster.

  Clunking Noises

  If Steering Tie Rod End develop excessive play or looseness, this can cause them to knock during takeoff, or when the vehicle is traveling over rough terrain. The clunking sound will continuously get louder as the component wears or until it eventually breaks.

  Steering Wandering

  Excessively worn Steering Tie Rod End can cause the vehicle’s steering alignment to shift, which may cause the steering to pull to the left or right when traveling down the road.

  

  ---