1.Fitting the Followingvehicle:2008-2016 Chrysler Town & Country2008-2017 Dodge Grand Caravan2.Package Includes:2x Front Wheel Hub Bearing -5132732x Front Sway Bar End Link -K72582x Front Inner Tie Rod End -ES806462x Outer Tie Rod End -ES8004031x Front Lower Control Arm And Ball Joint - Driver Side -k6220331x Front Lower Control Arm And Ball Joint - Passenger Side -k622034Notes For 08-17 Dodge Grand Caravan 10x Front Wheel Bearning Hub Sway Bar Tie Rod End
1.Fitting the Followingvehicle:
2008-2016 Chrysler Town & Country
2008-2017 Dodge Grand Caravan
2.Package Includes:
2x Front Wheel Hub Bearing -5132732x Front Sway Bar End Link -K72582x Front Inner Tie Rod End -ES806462x Outer Tie Rod End -ES8004031x Front Lower Control Arm And Ball Joint - Driver Side -k6220331x Front Lower Control Arm And Ball Joint - Passenger Side -k622034
Notes
(1).Please check the fitment chart above before payment makingsure all the suspension parts listed on this page are compatible with your automobile.
(2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests.
(3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is atthe bottom of thispage.
If you are interested with anyothersuspension parts, please click and saveour store.
Tie-Rod End Replacement Guideline:
If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely.
This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod.
Picture(A)
Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance.
1.Lift the vehicle and dismount the front axle wheels.
2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes.
Picture(B)
3.Dismount the front underride />4.Loosen the fastening nut from the tie rod and remove it completely.
5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator.
Picture(D)
6.Remove the clamp of the bellow on the steering gear.
7.Push the bellow towards the tie rod end.
Picture(E)
8.Unscrew the inner tie rod from the rack.
9.Clean the sealing face of the bellow at the steering gear.
Picture(F)
10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle.
Note:Always use new self-locking nuts and bolts for a reliable repair.
11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle />12.Mount the bellow and close the clamps with the appropriate special tool.
Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance.
Picture(H)
13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer.
Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure.
Tip:Secure the ball stud against twisting with a suitable tool.
Picture(I)
14.Mount the front underride guard.
15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer.
16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications.
17.Perform a test drive.
Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission.
Sway Bar Stabilizer Link Replacement Guideline:
While driving, the following signs may indicate a faulty sway barstabilizer link:
(1).Rattling and thumping noises on rough roads.
(2).Imprecise vehicle handling.
(3).Stronger inclination of the vehicle during cornering.
If the sway bar stabilizer link is found to be defective, it should be replaced as described below.
Picture(A)
1.Raise vehicle and remove front wheels.
Tip:Always check both stabilizer links and replace them in pairs if necessary.
2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few the lower fastening nut of the stabilizer link at the stabilizer and remove.
Tip:If the ball stud also starts to turn, hold it with a suitable tool.
4.Press stabilizer link out of torsion the upper fastening nut of the stabilizer link at the suspension strut and remove it.
Tip:If the ball stud also starts to turn, hold it with a suitable stabilizer link at suspension strut out of new stabilizer link at suspension stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer.
Tip:Secure the ball stud against twisting with a suitable new stabilizer link at stabilizer.
10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer.
Tip:Secure the ball stud against twisting with a suitable the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer.
Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension.
12.Conclude with a test drive.
Item SpecificsBrand :autoutdoorType :Control Arm & Ball Joint AssemblyUniversal Fitment :NoIncluded Hardware :Mounting HardwarePerformance Part :NoInterchange Part Number Part Number :tie rod end,rods ends,wheel hub bearing assembly,hubs bearingsOE/OEM Part Number :sway bar,Suspension arm Kit,replacing control arm car,rods endsFinish :CoatedManufacturer Warranty :10 YearPlacement on Vehicle :FrontManufacturer Part Number :ADD84132402RAdjustable :YesMaterial :Alloy SteelKit or Single Part :KitGreasable or Sealed :GreasableOE Spec or Performance/Custom :OE SpecSurface Finish :Polished, Rust ProtectedQuantity :10PcsItems Included :Mounting HardwareABS Sensor :Has ABS with tegral SensorBolt Circle Diameter :16.666665cm
Payment
- WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
- Instant Paypal payment is the preferred method of payment.
- We will only ship to the confirmed Paypal shipping address given with the payment.
- We do not offer local pickups.
Shipping
1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
3. The images shown are not the actual item and are for your reference only.
4. Fast shipping:All our packages use USPSPackage Service
5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
Returns
1. You have 7 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
3. We will refund your full winning offer amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from . OR, you may choose to have a replacement.
4.Return shipping is to be paid by the Buyer.
Contact Us
- We are always been trying to provide best service and reliable products for every customer.
- If you are satisfed with the product you recieved,please leave us positive response.
- If you are not satisfied for any reason, please do not be quick to leave negative or neutral response.We will work hard to make sure every customer 100 percent satisfied, and reslove any problem for you.
Shop CategoryStore Home Brake Rotors & Pads◈Brake Pads suspension kit◈suspension kit-chenjiao◈suspension kit-fu◈suspension kit-gxy◈Suspension Kits Exterior◈Spoilers & Wings◈Body Kits Turbos & Parts Axle Housings & Parts Motor◈Transfer Case Motor◈Running Board Motor◈Window Regulator Other
Hot Item For 2000-13 Chevy Impala 8PCS Front Lower Control Arm Sway Bar Tie Rod Ends Kit USD 86.99 15Pcs For 99-04 Jeep Grand Cherokee New Suspension Control Arm Tie Rod Sway Bar USD 136.88 For 1989-1994 1995 Toyota Pickup RWD 12pcs Suspension Tie Rods Center Link Kit USD 118.50 Fits 2002-2005 Honda Civic 12Pcs New Front Lower Control Arms Sway Bars Tie Rods USD 125.88 1998-2004 For Ford Ranger 10Pcs Front Control Arms Ball Joints Tie Rods Kit USD 98.00 New List Item K03-0470 Turbocharger Fits Ford Expedition 3.5L 2015-16 Navigator 3.5LRight Side USD 175.92 FITS Ford F250 Excursion 7.3 Powerstroke 1999-2003 GTP38 GTP38R Turbocharger USD 221.92 For 2021–on BMW G22 4-Series G80 M4 Coupe Carbon Fiber Trunk Spoiler USD 109.92 Fit for 2001-2007 Ford Escape Front Left Window Regulator with Motor 741-604 USD 39.84 Set of 2 For 2005-2014 Arctic Cat 400 Rear CV Axle Drive Shaft USD 108.92 For 08-17 Dodge Grand Caravan 10x Front Wheel Bearning Hub Sway Bar Tie Rod End
1.Fitting the Followingvehicle:
2008-2016 Chrysler Town & Country
2008-2017 Dodge Grand Caravan
2.Package Includes:
2x Front Wheel Hub Bearing -5132732x Front Sway Bar End Link -K72582x Front Inner Tie Rod End -ES806462x Outer Tie Rod End -ES8004031x Front Lower Control Arm And Ball Joint - Driver Side -k6220331x Front Lower Control Arm And Ball Joint - Passenger Side -k622034
Notes
(1).Please check the fitment chart above before payment makingsure all the suspension parts listed on this page are compatible with your automobile.
(2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests.
(3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is atthe bottom of thispage.
If you are interested with anyothersuspension parts, please click and saveour store.
Tie-Rod End Replacement Guideline:
If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely.
This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod.
Picture(A)
Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance.
1.Lift the vehicle and dismount the front axle wheels.
2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes.
Picture(B)
3.Dismount the front underride />4.Loosen the fastening nut from the tie rod and remove it completely.
5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator.
Picture(D)
6.Remove the clamp of the bellow on the steering gear.
7.Push the bellow towards the tie rod end.
Picture(E)
8.Unscrew the inner tie rod from the rack.
9.Clean the sealing face of the bellow at the steering gear.
Picture(F)
10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle.
Note:Always use new self-locking nuts and bolts for a reliable repair.
11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle />12.Mount the bellow and close the clamps with the appropriate special tool.
Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance.
Picture(H)
13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer.
Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure.
Tip:Secure the ball stud against twisting with a suitable tool.
Picture(I)
14.Mount the front underride guard.
15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer.
16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications.
17.Perform a test drive.
Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission.
Sway Bar Stabilizer Link Replacement Guideline:
While driving, the following signs may indicate a faulty sway barstabilizer link:
(1).Rattling and thumping noises on rough roads.
(2).Imprecise vehicle handling.
(3).Stronger inclination of the vehicle during cornering.
If the sway bar stabilizer link is found to be defective, it should be replaced as described below.
Picture(A)
1.Raise vehicle and remove front wheels.
Tip:Always check both stabilizer links and replace them in pairs if necessary.
2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few the lower fastening nut of the stabilizer link at the stabilizer and remove.
Tip:If the ball stud also starts to turn, hold it with a suitable tool.
4.Press stabilizer link out of torsion the upper fastening nut of the stabilizer link at the suspension strut and remove it.
Tip:If the ball stud also starts to turn, hold it with a suitable stabilizer link at suspension strut out of new stabilizer link at suspension stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer.
Tip:Secure the ball stud against twisting with a suitable new stabilizer link at stabilizer.
10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer.
Tip:Secure the ball stud against twisting with a suitable the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer.
Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension.
12.Conclude with a test drive.
Item SpecificsBrand :autoutdoorType :Control Arm & Ball Joint AssemblyUniversal Fitment :NoIncluded Hardware :Mounting HardwarePerformance Part :NoInterchange Part Number Part Number :tie rod end,rods ends,wheel hub bearing assembly,hubs bearingsOE/OEM Part Number :sway bar,Suspension arm Kit,replacing control arm car,rods endsFinish :CoatedManufacturer Warranty :10 YearPlacement on Vehicle :FrontManufacturer Part Number :ADD84132402RAdjustable :YesMaterial :Alloy SteelKit or Single Part :KitGreasable or Sealed :GreasableOE Spec or Performance/Custom :OE SpecSurface Finish :Polished, Rust ProtectedQuantity :10PcsItems Included :Mounting HardwareABS Sensor :Has ABS with tegral SensorBolt Circle Diameter :16.666665cm
PaymentShippingReturnsContact Us
- WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
- Instant Paypal payment is the preferred method of payment.
- We will only ship to the confirmed Paypal shipping address given with the payment.
- We do not offer local pickups.
1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
3. The images shown are not the actual item and are for your reference only.
4. Fast shipping:All our packages use USPSPackage Service
5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
1. You have 7 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
3. We will refund your full winning offer amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from . OR, you may choose to have a replacement.
4.Return shipping is to be paid by the Buyer.
- We are always been trying to provide best service and reliable products for every customer.
- If you are satisfed with the product you recieved,please leave us positive response.
- If you are not satisfied for any reason, please do not be quick to leave negative or neutral response.We will work hard to make sure every customer 100 percent satisfied, and reslove any problem for you.
Copyright of autoutdoor. All rights reserved.