Item on Vehicle:Fuel Tank3.Color:As picture shows4.Drive FitmentFor 2003-2005 Mercedes-Benz C230 L4 1.8LFor2002 Mercedes-Benz C230 L4 2.3LFor2006 Mercedes-Benz C230 V6 2.5LFor2002-2005 Mercedes-Benz C240 V6 2.6LFor2006-2007 Mercedes-Benz C280 V6 3.0LFor2001-2005 Mercedes-Benz C320 V6 3.2LFor2003-2005 Mercedes-Benz CLK320 V6 3.2LFor2007 Mercedes-Benz SLK280 V6 3.0LItem Include1.1xFuel Pump Module Assenbly For 2003-2005 Mercedes-Benz CLK320 V6 3.2L Fuel Pump Asembly & Sending Unit
Item on Vehicle:Fuel Tank
3.Color:As picture shows
4.Drive Type:Electrical
Vehicle Fitment
For 2003-2005 Mercedes-Benz C230 L4 1.8L
For2002 Mercedes-Benz C230 L4 2.3L
For2006 Mercedes-Benz C230 V6 2.5L
For2002-2005 Mercedes-Benz C240 V6 2.6L
For2006-2007 Mercedes-Benz C280 V6 3.0L
For2001-2005 Mercedes-Benz C320 V6 3.2L
For2003-2005 Mercedes-Benz CLK320 V6 3.2L
For2007 Mercedes-Benz SLK280 V6 3.0L
Item Include
1.1xFuel Pump Module Assenbly
When do you need to replace
1.Engine Stuttering
2.Engine Surges
3.Reduced Fuel Efficiency
4.High-Pitched Noises
5.Engine Won't Start
How to InstallFuel Pump
1.Park the vehicle on a firm, level surface and set the parking brake.
2.Find the fuel pump, then open the fuel cap and have an assistant turn the key to the ON position while you listen at the filler opening. If The fuel pump no sound is made, replacing the pump may be necessary.
3.Find and verify the fuel pump fuse and relay.
4.If the fuse is blown, replace it with a fuse of the same amperage. Check fuel pump operation. If the fuel pump works, your job is done.
5.If the fuse and relay are functional, check for power and ground at the fuel pump. Removing the fuel tank or the back seat may be necessary. If there is power and ground at the pump, then the pump is faulty.
6.Relieve the fuel system pressure. Disconnect the negative battery cable.
7.Siphon or drain as much fuel as possible from the fuel tank. Disconnect the filler tube hose and the electrical connection to the pump.
8.Support the fuel tank with a jack and a block of wood. Remove any retaining straps or bolts holding the tank to the frame. Lower the tank.
9.Disconnect the fuel lines and remove the fuel pump from the tank.
10.Compare the new fuel pump with the original to verify that you have the correct part. Install the new fuel pump.
11.Connect the fuel lines to the pump. Lift the fuel tank up and install the retaining strap. Reconnect the filler tube hose and the electrical connector.
12.Reconnect the negative battery cable. Fill the tank with gas. Conduct a road test to confirm a successful you have any question about the product, please contact us before buying, we will give you a best reply in time.
2.We are galde to offer quality service and vehicle parts to you, any sale questions please message us before open case or response, we will give you the best solution
For 2003-2005 Mercedes-Benz CLK320 V6 3.2L Fuel Pump Asembly & Sending Unit
Item on Vehicle:Fuel Tank
3.Color:As picture shows
4.Drive Type:Electrical
Vehicle Fitment
For 2003-2005 Mercedes-Benz C230 L4 1.8L
For2002 Mercedes-Benz C230 L4 2.3L
For2006 Mercedes-Benz C230 V6 2.5L
For2002-2005 Mercedes-Benz C240 V6 2.6L
For2006-2007 Mercedes-Benz C280 V6 3.0L
For2001-2005 Mercedes-Benz C320 V6 3.2L
For2003-2005 Mercedes-Benz CLK320 V6 3.2L
For2007 Mercedes-Benz SLK280 V6 3.0L
Item Include
1.1xFuel Pump Module Assenbly
When do you need to replace
1.Engine Stuttering
2.Engine Surges
3.Reduced Fuel Efficiency
4.High-Pitched Noises
5.Engine Won't Start
How to InstallFuel Pump
1.Park the vehicle on a firm, level surface and set the parking brake.
2.Find the fuel pump, then open the fuel cap and have an assistant turn the key to the ON position while you listen at the filler opening. If The fuel pump no sound is made, replacing the pump may be necessary.
3.Find and verify the fuel pump fuse and relay.
4.If the fuse is blown, replace it with a fuse of the same amperage. Check fuel pump operation. If the fuel pump works, your job is done.
5.If the fuse and relay are functional, check for power and ground at the fuel pump. Removing the fuel tank or the back seat may be necessary. If there is power and ground at the pump, then the pump is faulty.
6.Relieve the fuel system pressure. Disconnect the negative battery cable.
7.Siphon or drain as much fuel as possible from the fuel tank. Disconnect the filler tube hose and the electrical connection to the pump.
8.Support the fuel tank with a jack and a block of wood. Remove any retaining straps or bolts holding the tank to the frame. Lower the tank.
9.Disconnect the fuel lines and remove the fuel pump from the tank.
10.Compare the new fuel pump with the original to verify that you have the correct part. Install the new fuel pump.
11.Connect the fuel lines to the pump. Lift the fuel tank up and install the retaining strap. Reconnect the filler tube hose and the electrical connector.
12.Reconnect the negative battery cable. Fill the tank with gas. Conduct a road test to confirm a successful you have any question about the product, please contact us before buying, we will give you a best reply in time.
2.We are galde to offer quality service and vehicle parts to you, any sale questions please message us before open case or response, we will give you the best solution
Item SpecificsDrive Type :ElectricalFuel Type :GasolinePressure :130-140Flow Rate :50-60Working Principle :Fuel pump module is made with premium materials that meet or exceed OEM standards for durability and reliability. Fuel pumps can ensure proper fuel flow and pressure, thereby improving fuel efficiency, reducing fuel consumption andInspection precautions :When inspecting the fuel pump , it is necessary to check whether the valve is working properly , whether the pressure limiter is set correctly , and whether there are any signs of leakage .Outlet Type :Hose BarbOutlet Size :5/8Inlet Type :StrainerInlet Count :1Outlet Count :1Terminal Type :FlatPin Count :4Terminal Gender :FemaleConnector Shape :SquareConnector Gender :MaleInternal Or External Strainer :InternalIn Tank or External :In TankCondition :NewWiring Harness Included :NoVoltage :12 VGasket or Seal Included :YesFloat Included :YesPackage Contents :Fuel Pump Module Assembly w/Float Arm,SealInterchange Part Number Spec or Performance/Custom :OE SpecPackaging includes :As shown in the picturePackaging?Type :BoxQuantity :Sold individuallySuperseded Part Number Item :NoRelated Parts :Fuel Pump; Fuel Sending Unit; Strainer; Seal RingEasy to install :Fuel Pump Assembly No professional tools are required , installation is convenient and quick, saving you valuable time+Fitment Type :Direct ReplacementManufacturer Warranty :1 YearPlacement on Vehicle :Fuel TankColour :WhiteItems Included :Mounting HardwareType :Fuel PumpBrand :topcn-autopartsManufacturer Part Number :TA11082507PCustomer attention :Hello, Please use the tool (at the top of the page) & enter Year , Make, Model, Trim, Engine Size to verify & was approved by , also view the notes beside the vehicle you have selected, It is the buyer's responsibility to verify.
Shipping
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-5 business days.
3.Local pick up is not available.
4.Orders to the rest of world may be shipped out from our warehouse in HongKong.
5.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to offerding/buying.
Payment
1. We stand behind every product we sell.
2. All of our brand new items come with a 30-Days money-back guarantee.
Customer Services
Q: How do I pay for my purchase?
A: MY store acceptmultiplepaymentmethods.
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my "-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item.
response
1. We will leave response once we get your payment.
2. If you are dissatisfied for any reason, please do not be quick to leave response. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive response to all our customers.
3. If you are satisfied with the product you received, please leave us response.
DESCRIPTIONPAYMENTSHIPPINGRETURN POLICYCONTACT US Shop CategoryStore Home Ignition Coils complete struts Radiator Support Wheel Hub Bearing Wheel Adaptor Oxygen Sensor Towing mirrors Fuel pump assembly Lift supports Starter Key or key case struts CV Boot Kit wheel lug nuts Cylinder Piston Gasket Kit Cylinder Head Gasket Sets CV Axle Door handle Radiator fastener UTV & ATV Brake System Parts▷Brake Pads♢Kevlar Carbon Brake Pads Regulator Rectifier blower motor fan blower motor resistor suspension kit◈suspension kits◈suspension cj◈suspension gxy◈suspension fu AC Compressor Brake system◈Brake Rotors◈Brake Pads◈Brake Rotors and Pads◈Brake Drum Air Suspensions Nerf Bars & Running Boards Spark Plugs ATV Rear Axle Window Switch Mass Air Flow Sensor-MAF Window Regulator Alternator Leveling Lift Kit Fuel Injector Coilover Car Tools Windshield Wiper Motor Thermostat Housing Radiator Coolant Tank Fuel Tank Pipe Valve Cover Door Lock Actuator Power Steering Pump Variable Timing Solenoid (VVT) Electric Water Pump Timing Chain Kits Timing Belt Kits Water Pumps Oil Pump Tire Pressure Sensor Throttle Body Harmonic Balancer Motorcycle Carburetor & Parts Intake Manifold Cooling Fan Cooling Fan Clutch Hydraulic Lifter&Roller Lifter Suspension+Strut+Bearing Head/Fog/Tail Light Assembly HVAC Parking sensor Car Antenna ABS Wheel Speed Sensor PTO Clutch Spoilers & Wings Tensioners Knock Sensor Turbocharger Crankshaft Position Sensor Camshaft Position Sensor MAP Sensor Oil Pressure Sensor Throttle Position Sensor Stator Catalytic Converter idle air control valve Transfer Case Shift Motor Secondary Air Injection Pump Consoles & Parts Roof rack Bumper Steering Rack Air Diesel Heater Engine Mount Air Cleaner Filter Box Cylinder Piston Kit Jack Stands Sun Visor Window Visor Air Intake Hose Cold Air Intake Kit Horns Steering U-Joint Fuel Cell Tank Height Level Sensor Temperature Sensor Driveshaft Calipers & Rotors◈Calipers & Rotors Pads Ballast module Dipstick Camshaft & Crankshaft Rocker Arm Electric Motor LED headlight Assembly Wheel Hub Bearing Knuckle Foot Rest Pedal water Pump Impeller Strut Mount Splash Guards & Mud Flaps Heater Cores Evaporators vehicle speed sensor Light Bar Mount Bracket Sensor-8 Steering Shaft transmission filter snorkel air intake CDI BOX Spindle Other Golf Cart Parts Intercoolers 4 pcs wheel hub bearing Window Weatherstrip Seal Fender Flares jumper cable Tonneau Cover Front Bumper Lip dash cover primary drive clutch golf AC Compressor Control Valve+A Garden Water Pump Lower Kits & Parts Cargo Cover Leaf Springs Hub Caps winch CV Joint Axle Power Brake Booster CV AXLE-COPPY Wheel Rim Lights◈Side/Cab Marker Lights◈Instrument Panel Lights◈Third Brake Lights◈Interior Lights◈Led Headlights Air Dryer steering knuckle-7 Bed Step Headlight Assembly-II Trunk Mat RV Awning Fabric Trailer Hitch Coil Springs Brake System Parts◈Brake Calipers◈Brake Drums & Brake Shoes◈Brake Pads & Brake Shoes Air Filter Fuel Vapor Charcoal Canister A/C Refrigerant Discharge Hose Brake Dust Shield RV Cover Leaf Spring Shackle Kit Mower Blades Deck rebuild kit truck box Radiator Shutter Deck Belt OtherHot Item Turbocharger Turbo For 2011-2015 Chevrolet Cruze LTZ Sedan 4-Door 1.4L 1364CC USD 160.90 Throttle Body for Chrysler Cirrus 2.4L 2007-2010 Dodge Caliber 1.8L 2007-2009 USD 47.99 2x Front Hood Lift Supports Shocks Struts For Dodge Ram 1500 2500 3500 4500 5500 USD 16.66 2x Front Hood Gas Lift Supports Struts Shocks Springs For Dodge Ram 02-10 4364 USD 16.82 Upstream & Downstream Oxygen O2 02 Sensor For 2001-2005 Honda Civic 1.7L D17A7 USD 21.25 New List Item Drill Vented Fits Dodge For Grand Caravan 2008 - 2016 2X Brake Rotors Front USD 81.11 EPA Catalytic Converter Fits 2012-2016 BMW 228i 320i 328i xDrive 428i 2.0L 17546 USD 315.67 Fits Dodge For Nitro 2007 2008 2009 2010 2011 2012 Solid Rear Brake Rotors 2X USD 78.86 Drill 2003-2011 For Ford Crown Victoria Fits Lincoln Town Car Front Brake Rotors USD 99.82 Catalytic Converter For 2013 2014-2020 Ford Fusion 2.5L EPA OBDII Exhaust Front USD 148.26 For 2003-2005 Mercedes-Benz CLK320 V6 3.2L Fuel Pump Asembly & Sending Unit
Item on Vehicle:Fuel Tank
3.Color:As picture shows
4.Drive Type:Electrical
Vehicle Fitment
For 2003-2005 Mercedes-Benz C230 L4 1.8L
For2002 Mercedes-Benz C230 L4 2.3L
For2006 Mercedes-Benz C230 V6 2.5L
For2002-2005 Mercedes-Benz C240 V6 2.6L
For2006-2007 Mercedes-Benz C280 V6 3.0L
For2001-2005 Mercedes-Benz C320 V6 3.2L
For2003-2005 Mercedes-Benz CLK320 V6 3.2L
For2007 Mercedes-Benz SLK280 V6 3.0L
Item Include
1.1xFuel Pump Module Assenbly
When do you need to replace
1.Engine Stuttering
2.Engine Surges
3.Reduced Fuel Efficiency
4.High-Pitched Noises
5.Engine Won't Start
How to InstallFuel Pump
1.Park the vehicle on a firm, level surface and set the parking brake.
2.Find the fuel pump, then open the fuel cap and have an assistant turn the key to the ON position while you listen at the filler opening. If The fuel pump no sound is made, replacing the pump may be necessary.
3.Find and verify the fuel pump fuse and relay.
4.If the fuse is blown, replace it with a fuse of the same amperage. Check fuel pump operation. If the fuel pump works, your job is done.
5.If the fuse and relay are functional, check for power and ground at the fuel pump. Removing the fuel tank or the back seat may be necessary. If there is power and ground at the pump, then the pump is faulty.
6.Relieve the fuel system pressure. Disconnect the negative battery cable.
7.Siphon or drain as much fuel as possible from the fuel tank. Disconnect the filler tube hose and the electrical connection to the pump.
8.Support the fuel tank with a jack and a block of wood. Remove any retaining straps or bolts holding the tank to the frame. Lower the tank.
9.Disconnect the fuel lines and remove the fuel pump from the tank.
10.Compare the new fuel pump with the original to verify that you have the correct part. Install the new fuel pump.
11.Connect the fuel lines to the pump. Lift the fuel tank up and install the retaining strap. Reconnect the filler tube hose and the electrical connector.
12.Reconnect the negative battery cable. Fill the tank with gas. Conduct a road test to confirm a successful you have any question about the product, please contact us before buying, we will give you a best reply in time.
2.We are galde to offer quality service and vehicle parts to you, any sale questions please message us before open case or response, we will give you the best solution
Item SpecificsDrive Type :ElectricalFuel Type :GasolinePressure :130-140Flow Rate :50-60Working Principle :Fuel pump module is made with premium materials that meet or exceed OEM standards for durability and reliability. Fuel pumps can ensure proper fuel flow and pressure, thereby improving fuel efficiency, reducing fuel consumption andInspection precautions :When inspecting the fuel pump , it is necessary to check whether the valve is working properly , whether the pressure limiter is set correctly , and whether there are any signs of leakage .Outlet Type :Hose BarbOutlet Size :5/8Inlet Type :StrainerInlet Count :1Outlet Count :1Terminal Type :FlatPin Count :4Terminal Gender :FemaleConnector Shape :SquareConnector Gender :MaleInternal Or External Strainer :InternalIn Tank or External :In TankCondition :NewWiring Harness Included :NoVoltage :12 VGasket or Seal Included :YesFloat Included :YesPackage Contents :Fuel Pump Module Assembly w/Float Arm,SealInterchange Part Number Spec or Performance/Custom :OE SpecPackaging includes :As shown in the picturePackaging?Type :BoxQuantity :Sold individuallySuperseded Part Number Item :NoRelated Parts :Fuel Pump; Fuel Sending Unit; Strainer; Seal RingEasy to install :Fuel Pump Assembly No professional tools are required , installation is convenient and quick, saving you valuable time+Fitment Type :Direct ReplacementManufacturer Warranty :1 YearPlacement on Vehicle :Fuel TankColour :WhiteItems Included :Mounting HardwareType :Fuel PumpBrand :topcn-autopartsManufacturer Part Number :TA11082507PCustomer attention :Hello, Please use the tool (at the top of the page) & enter Year , Make, Model, Trim, Engine Size to verify & was approved by , also view the notes beside the vehicle you have selected, It is the buyer's responsibility to verify.
ShippingPaymentReturnsCustomer Servicesresponse
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-5 business days.
3.Local pick up is not available.
4.Orders to the rest of world may be shipped out from our warehouse in HongKong.
5.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to offerding/buying.
Weacceptmultiplepaymentmethods.
1. We stand behind every product we sell.
2. All of our brand new items come with a 30-Days money-back guarantee.
Q: How do I pay for my purchase?
A: MY store acceptmultiplepaymentmethods.
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my "-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item.
1. We will leave response once we get your payment.
2. If you are dissatisfied for any reason, please do not be quick to leave response. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive response to all our customers.
3. If you are satisfied with the product you received, please leave us response.
Copyright of Topcn-autoparts. All rights reserved.
