PRO TIP:This step usually depressurizes the fuel system in multi-port fuel injected vehicles, but your engine may vary. Check your repair manual to be sure.
2.Make sure the engine is cold enough to touch. Disconnect the battery.
3.Remove plastic engine covers using appropriate socket. Set covers aside.
4.Use pliers to disconnect the electrical connector on each injector.
5. Lift the fuel rail off of the intake manifold, bringing the injectors with it. This takes a good amount of force, as the injectors are attached to the rail, and the sprayer tips are a snug fit in the intake manifold. Don't use so much force, though, that you deform or bend the fuel rail. Pulling straight up (as the injector is oriented) makes for easier removal.
6.Examine the injector. If you see a small metal clip that looks like a staple, use a small flathead screwdriver to remove or depress the clip. Grasp the injector and work back and forth while pulling to remove from the fuel rail. The injector and rail will drip, so have shop towels ready.
PRO TIP:Before installing the new fuel injectors, dip the fuel injector tip (sprayer end) into a small amount ofengine oil. This will wet the seals, preventing leaks.
7.Press the injector into the rail until it stops. Attach the metal clip, if equipped.
8.Reattach the fuel rail. Line up all the injectors over their respective holes, then press each injector until they slide into place.
9.Bolt down fuel rail. Reattach fuel line. Plug in fuel injector electrical connections.
10.Reconnect battery.
11.Turn the key to the on position and wait 10 seconds before turning to engine start. This will allow the fuel pump to refill the lines and fuel rails before the engine cranks.
12.After the engine drops to the normal idle RPM, turn the engine off. Take a flashlight and check all the injectors for fuel leaks.
A leaking or plugged fuel injector causes the related cylinder to run richor lean, both of which can cause long-term problems that require extensive repairs.
In addition, your car’s performance will suffer and your Check Engine light will remain on until the repair is performed.
Yes & No. All of our fuel injectors are ready to operate upon installation.
Starting the engine and letting it idle for a minimum of 20 minutes is the best thing to do after installing new injectors. This will push the aerated fuel out of the injector nozzle. Failure to do this may create a low/no-fuel condition, which could cause internal damage to the injectors. The new fuel injectors will perform great initially, and you will continue to see increased performance up to 1000-3000 miles as the injectors continue to break-in.
Yes, a fuel injector upgrade is a great option to help add miles-per-gallon or restore lost power and torque in older or high-mileage engines. The first thing to know is "upgrading" does not mean changing the injector flow-rate. Upgrading means replacing old, worn, OEM fuel injectors with a new set of fuel injectors. This upgrade can improve the overall performance of an older engine.
1. Diesel Fuel Injectors
Modern diesel fuel injectors are used to atomize and inject or spray diesel (which is heavier fuel than gasoline) directly into the combustion chamber of the diesel engine for compression ignition (no spark plugs).
Diesel fuel injectors require much higher injection pressure (up to 30,000 psi) than gasoline injectors as diesel is heavier than gasoline, and it takes much higher pressure to atomize the fuel.
2. Gasoline Fuel Injectors
Gasoline fuel injectors are used to inject or spray gasoline directly (GDI) or through intake manifold (multi-port) or throttle body into the combustion chamber for combustion which is ignited by spark.
The design of gasoline injectors varies by type… the newer GDI injectors use a multi holed nozzle, the multi-port and throttle body use a pointless style nozzle. Gasoline injection pressures are much lower than Diesel…3000 psi for GDI and 35 psi for Pinter style.
It is not easy to diagnose a fuel injector as the symptoms it causes can be like a bad spark plug or ignition coil, meaning, one of the cylinders is not firing. If it is related to a clogged fuel injectorit is due to old fuel being run through the engine, resulting in residue getting stuck inside the injector or its filter basket. If a fuel injector becomes fully clogged it will have to be removed from the vehicle and be professionally cleaned, as additives and fuel tank introduced injection cleaners will not be able to clear the clog, as they cannot pass through at all.
This can be an extremely dangerous situation. If the fuel injectors are leaking externally, you should not drive your vehicle. While a leaking injector will cause issues like that of a dirty one, you will often be able to smell gas or diesel under the hood or even spot a leak, depending on your make and model. Externally leaking injectors pose a fire risk and need to be completely replaced.
A fuel injector is a device for atomizing and injecting fuel into an internal combustionengine. It's consistently under pressure.
It is advisable that when you plan to change the fuel injectors, change them all. Do not change just the ones that are malfunctioning. Pairing brand new injectors with old ones could cause inconsistent performance and a less than satisfactory driving experience.
- Replacement fuel injectors
- Fuel injector seals
- Ratchet & socket set
- Flathead screwdriver
- Pliers
metal rod over the fuel injectors is the fuel rail. Use the socket and ratchet to remove the bolts and brackets holding the fuel rail in place. Depending on the model, some engines will need the fuel line disconnected from the fuel rail in order to move the rail.PRO TIP:This step usually depressurizes the fuel system in multi-port fuel injected vehicles, but your engine may vary. Check your repair manual to be sure.
2.Make sure the engine is cold enough to touch. Disconnect the battery.
3.Remove plastic engine covers using appropriate socket. Set covers aside.
4.Use pliers to disconnect the electrical connector on each injector.
5. Lift the fuel rail off of the intake manifold, bringing the injectors with it. This takes a good amount of force, as the injectors are attached to the rail, and the sprayer tips are a snug fit in the intake manifold. Don't use so much force, though, that you deform or bend the fuel rail. Pulling straight up (as the injector is oriented) makes for easier removal.
6.Examine the injector. If you see a small metal clip that looks like a staple, use a small flathead screwdriver to remove or depress the clip. Grasp the injector and work back and forth while pulling to remove from the fuel rail. The injector and rail will drip, so have shop towels ready.
PRO TIP:Before installing the new fuel injectors, dip the fuel injector tip (sprayer end) into a small amount ofengine oil. This will wet the seals, preventing leaks.
7.Press the injector into the rail until it stops. Attach the metal clip, if equipped.
8.Reattach the fuel rail. Line up all the injectors over their respective holes, then press each injector until they slide into place.
9.Bolt down fuel rail. Reattach fuel line. Plug in fuel injector electrical connections.
10.Reconnect battery.
11.Turn the key to the on position and wait 10 seconds before turning to engine start. This will allow the fuel pump to refill the lines and fuel rails before the engine cranks.
12.After the engine drops to the normal idle RPM, turn the engine off. Take a flashlight and check all the injectors for fuel leaks.
How important is replacing your fuel Injectors?
A leaking or plugged fuel injector causes the related cylinder to run richor lean, both of which can cause long-term problems that require extensive repairs.
In addition, your car’s performance will suffer and your Check Engine light will remain on until the repair is performed.
Is there a break-in period with my new fuel injectors?
Yes & No. All of our fuel injectors are ready to operate upon installation.
Starting the engine and letting it idle for a minimum of 20 minutes is the best thing to do after installing new injectors. This will push the aerated fuel out of the injector nozzle. Failure to do this may create a low/no-fuel condition, which could cause internal damage to the injectors. The new fuel injectors will perform great initially, and you will continue to see increased performance up to 1000-3000 miles as the injectors continue to break-in.
Can you upgrade fuel injectors?
Yes, a fuel injector upgrade is a great option to help add miles-per-gallon or restore lost power and torque in older or high-mileage engines. The first thing to know is "upgrading" does not mean changing the injector flow-rate. Upgrading means replacing old, worn, OEM fuel injectors with a new set of fuel injectors. This upgrade can improve the overall performance of an older engine.
There are 2 types of fuel injectors:
1. Diesel Fuel Injectors
Modern diesel fuel injectors are used to atomize and inject or spray diesel (which is heavier fuel than gasoline) directly into the combustion chamber of the diesel engine for compression ignition (no spark plugs).
Diesel fuel injectors require much higher injection pressure (up to 30,000 psi) than gasoline injectors as diesel is heavier than gasoline, and it takes much higher pressure to atomize the fuel.
2. Gasoline Fuel Injectors
Gasoline fuel injectors are used to inject or spray gasoline directly (GDI) or through intake manifold (multi-port) or throttle body into the combustion chamber for combustion which is ignited by spark.
The design of gasoline injectors varies by type… the newer GDI injectors use a multi holed nozzle, the multi-port and throttle body use a pointless style nozzle. Gasoline injection pressures are much lower than Diesel…3000 psi for GDI and 35 psi for Pinter style.
Clogged Fuel Injectors
It is not easy to diagnose a fuel injector as the symptoms it causes can be like a bad spark plug or ignition coil, meaning, one of the cylinders is not firing. If it is related to a clogged fuel injectorit is due to old fuel being run through the engine, resulting in residue getting stuck inside the injector or its filter basket. If a fuel injector becomes fully clogged it will have to be removed from the vehicle and be professionally cleaned, as additives and fuel tank introduced injection cleaners will not be able to clear the clog, as they cannot pass through at all.
Leaking Fuel Injectors
This can be an extremely dangerous situation. If the fuel injectors are leaking externally, you should not drive your vehicle. While a leaking injector will cause issues like that of a dirty one, you will often be able to smell gas or diesel under the hood or even spot a leak, depending on your make and model. Externally leaking injectors pose a fire risk and need to be completely replaced.
Fits Applications
With Fuel Return Line
Chevrolet Astro 1996-2001 V6 4.3L Conversion Kit to MFI
Chevrolet Astro 2002-2005 V6 4.3L
Chevrolet Blazer 1996-2000 V6 4.3L
Chevrolet Blazer 2001-2002 V6 4.3L Conversion Kit to MFI
Chevrolet Blazer 2003-2005 V6 4.3L
Chevrolet C1500 1996-1998 V6 4.3L Conversion Kit to MFI
Chevrolet Express 1500 1996-2002 V6 4.3L Conversion Kit to MFI
Chevrolet Express 1500 2003-2014 V6 4.3L
Chevrolet Express 2500 1996-2002 V6 4.3L Conversion Kit to MFI
Chevrolet Express 2500 2003-2005 V6 4.3L
Chevrolet K1500 1996-1998 V6 4.3L Conversion Kit to MFI
Chevrolet P30 1996-1999 V6 4.3L Conversion Kit to MFI
Chevrolet S10 1996-2002 V6 4.3L Conversion Kit to MFI
Chevrolet S10 2003-2004 V6 4.3L
Chevrolet Silverado 1500 1999-2001 V6 4.3L Conversion Kit to MFI
Chevrolet Silverado 1500 2002 V6 4.3L VIN: W, Conversion Kit to MFI
Chevrolet Silverado 1500 2002-2013 V6 4.3L 2002: VIN: X
GMC C1500 1996-1998 V6 4.3L Conversion Kit to MFI
GMC Jimmy 1996-2002 V6 4.3L Conversion Kit to MFI
GMC K1500 1996-1998 V6 4.3L Conversion Kit to MFI
GMC P3500 1996-1999 V6 4.3L Conversion Kit to MFI
GMC Safari 1996-2001 V6 4.3L Conversion Kit to MFI
GMC Safari 2002-2005 V6 4.3L
GMC Savana 1500 1996-2002 V6 4.3L Conversion Kit to MFI
GMC Savana 1500 2003-2013 V6 4.3L
GMC Savana 2500 1996-2002 V6 4.3L Conversion Kit to MFI
GMC Savana 2500 2003-2006 V6 4.3L
GMC Sierra 1500 1999-2002 V6 4.3L Conversion Kit to MFI. 2002: VIN: W
GMC Sierra 1500 2002-2013 V6 4.3L 2002: VIN: X
GMC Sonoma 1996-2002 V6 4.3L Conversion Kit to MFI
GMC Sonoma 2003-2004 V6 4.3L
Isuzu Hombre 1997-2000 V6 4.3L Conversion Kit to MFI
Oldsmobile Bravada 1996-2001 V6 4.3L Conversion Kit to MFI
Item SpecificsBrand scitooManufacturer Warranty 1YearInterchange Part Number 5943BY/12568332 17113673 322-04819 217-3028,Manufacturer Part Number CB15149101SType Fuel InjectorVintage Car Part NOConnector Color As Shown in the PictureConnector Type GasolineUniversal Fitment YesInjector Design Metal & composite plasticBundle Listing NoFitment Type Direct ReplacementOE/OEM Part Number FJ503, 12568332, 19210688, 833221056Placement on Vehicle FrontFuel delivery type Fog-type sprayOE Spec or Performance/Custom OE Spec
Shipping WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3.Local pick up is not available.
4.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to offerding/buying.]
Payment 1.We accept multiple payment methods, such as PayPal, VISA, Master Card, etc..
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 7 days as sale ended or order might be delayed.
Returns 1.All of our brand new items come with a 60-Days money-back guarantee.
2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before offerding.
3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.
4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.
5.Shipping& handling cost are not refundable.
6.Man-made damage by abuse or wrong operation is not covered by this warranty.
7.No product liability insurance is assumed.
8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ]
Customer Services Q: How do I pay for my purchase?
A: MY store accepts PayPal, VISA, Master Card, etc..
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my "-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ]
response 1. We will leave a response once we get your payment.
2. If you are dissatisfied for any reason, please do contact us aresponse. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a response to all our customers.
3. If you are satisfied with the product you received, wish you can leave us a response.
Shop CategoryStore Home A/C Expansion Valve ABS Wheel Speed Sensor AC Compressor AC Compressor Control Valve+A AC Condenser & Radiator◈AC Condenser◈AC Condenser & Radiator◈Radiator Adjustable Control /Camber Arm Air Cleaner Filter Box Air Diesel Heater Air Dryer Air suspension valves solenoid Air suspensions Alternators ATV Brake Caliper ATV Brake Master Cylinder ATV Ignition Switch ATV Rear Wheel Axle ATV Tires Auto parts◈Blower Motor◈Coilover◈complete struts◈CV Axle◈Fuel Pump Assembly◈Ignition Coil◈Key Case◈Starter◈strut/absorber shock◈Struts/Absorbers Shocks◈Towing Mirrors◈Trunk Floor Mats◈Window Switch ball joint Ballast module Bed Step Blower Motor & Resistor Brake Oil Hose Brake Pads & Rotors◈Brake Pad Sensor◈Brake Pads◈Brake Rotors◈Brake Rotors and Pads Brake System Parts◈Brake Calipers◈Brake Drums & Brake Shoes◈Brake Pads & Brake Shoes Bumper C Notch & Flip Kit Camshaft & Crankshaft Camshaft Position Sensor Car Antenna Car Carburetor Car Cover Car Seat Cover Car Tools Cargo Cover CDI BOX Consoles & Parts Control Arms & Parts Cooling Fan Cooling Fan Clutch Crankcase Vent Valve Crankshaft Position Sensor CV axle+Brake Pads/Rotors Cylinder Head Gasket Sets Cylinder Piston Gasket Kit Cylinder Piston Kit dash cover Dipstick Door check stop Door handle Door Lock Actuator Driveshaft Electric Water Pump Electrical & Test Equipment Engine Mount Evaporators Fastener Fender Flares fog lights Foot Rest Pedal Front Bumper Lip Fuel Injectors Fuel Pressure Regulator Fuel Tank Pipe Fuel Valve& Petcocks Fuse Holder Box Glow Plug golf Harmonic Balancer headlight motorcycle Heater Control Valve Heater Cores Height Level Sensor Home & Garden◈Portable Fans Horns & Sirens Hot Stapler Hub Caps HVAC Hydraulic Lifter&Roller Lifter idle air control valve Ignition Distributor Intake Exhaust Valves Intercooler Jack Stands jumper cable Knock Sensor LED headlight Assembly leveling lift kit leveling lift kit+shock struts License Plate Frame lift support Light Bar Mount Bracket Lights◈Exterior Lights◈Instrument Panel Lights◈Interior Lights◈Led Headlights◈Side/Cab Marker Lights◈Special Model Lights◈Third Brake Lights Lower Kits & Parts MAP Sensor Mass Air Flow Sensor Motorcycle Brake Clutch Lever Motorcycle Carburetor & Parts Nerf Bars & Running Boards O Ring Off-Road Axles & Half Shafts Oil Catch Can Tank Oil Cooler Oil Fuel Hose Line Oil Pan Oil Pressure Sensor Oil Pump Other Golf Cart Parts Oxygen Sensors Parking sensor Pillar Posts Power Brake Booster Power Steering Pump Pressure Tester Gauge primary drive clutch PTO Clutch Purge Valve Radiator Coolant Tank Radiator Hose Radiator Support Regulator Rectifier Removal Open Tools Rocker Arm Roof rack Rubber Seal Strip Running Board Motor Secondary Air Injection Pump Sensor-8 snorkel air intake Spark Plug Ignition Wire Spindle Splash Guards & Mud Flaps Spoilers & Wings Starter Relay Solenoid Stator Steering Knuckle steering knuckle-7 Steering Rack Steering Shaft Steering U-Joint Steering Wheel Steering Wheel Hub Strut Mount Strut Tie Bar Sun Visor suspension 5 BIN◈chenjiao suspension kit◈suspension cj◈suspension fu◈suspension gxy◈Suspension Kits Suspension+Strut+Bearing Temperature Sensor Tensioners Thermostat Housing Throttle Body Throttle Position Sensor Timing Belt Kits Timing Chain Kits Tire Pressure Gauge Tire Pressure Sensor Tonneau Cover Transfer Case Shift Motor transmission filter transmission kit trim tilt motor Turbocharger Valve Cover Variable Timing Solenoid (VVT) vehicle speed sensor water Pump Impeller Water Pumps wheel hub bearing Wheel Hub Bearing Knuckle Wheel Hub Centric Rings Wheel lug nut Wheel Spacers winch Window Regulator window visor Windshield Outer Trim Windshield Wiper Motor Windshields OtherNew List Item Fits Honda Civic 2015-2012 Front Right with Motor Power Window Regulator USD 38.98 4x Front Rear Air Suspension Struts w/ADS For Mercedes W166 ML350 500 X166 GL450 USD 548.74 4x Rear Air Suspension Struts Spring Bag For Toyota Land Cruiser 150 Lexus GX460 USD 242.25 3x Air Shock Strut + Suspension Compressor For Ford Expedition Lincoln Navigator USD 459.99 For Subaru Crosstrek 2016-2017 Window Regulator & Motor Assembly Front Right USD 43.98 Hot Item Fuel Pump for Chevy S10 GMC Sonoma Hombre 4.3L 97-02 for Isuzu Hombre 4.3L 97-20 USD 33.39 Inline Universal High Pressure Fuel Pump With Installation Kit 0580464070 USD 20.95 Alternator for 110Amp Chrome Street Rod GM 305 350 BBC SBC 1 Wire Self Exciting USD 68.39 2pc 3157 4114 4157 LED DRL Driving Daytime Running Light Bulbs 12SMD 6000K White USD 8.39 12V Universal Fuel Pump Gas Diesel Inline Low Pressure HEP-02A BHEP-02A USD 11.59 Warranty 6 Spider Fuel Injectors For 1999-2013 Chevrolet Silverado GMC Sierra 1500 4.3L What is a fuel injector?
A fuel injector is a device for atomizing and injecting fuel into an internal combustionengine. It's consistently under pressure.
Symptoms you require fuel injector replacement
- Check Engine Light is illuminated;
- The engine runs rough or there’s a dead miss in a cylinder;
- There’s a raw fuel smell from the engine or the exhaust.
How to Replace Fuel Injectors?
Tips to remember
It is advisable that when you plan to change the fuel injectors, change them all. Do not change just the ones that are malfunctioning. Pairing brand new injectors with old ones could cause inconsistent performance and a less than satisfactory driving experience.
WHAT YOU'LL NEED
- Replacement fuel injectors
- Fuel injector seals
- Ratchet & socket set
- Flathead screwdriver
- Pliers
metal rod over the fuel injectors is the fuel rail. Use the socket and ratchet to remove the bolts and brackets holding the fuel rail in place. Depending on the model, some engines will need the fuel line disconnected from the fuel rail in order to move the rail.PRO TIP:This step usually depressurizes the fuel system in multi-port fuel injected vehicles, but your engine may vary. Check your repair manual to be sure.
2.Make sure the engine is cold enough to touch. Disconnect the battery.
3.Remove plastic engine covers using appropriate socket. Set covers aside.
4.Use pliers to disconnect the electrical connector on each injector.
5. Lift the fuel rail off of the intake manifold, bringing the injectors with it. This takes a good amount of force, as the injectors are attached to the rail, and the sprayer tips are a snug fit in the intake manifold. Don't use so much force, though, that you deform or bend the fuel rail. Pulling straight up (as the injector is oriented) makes for easier removal.
6.Examine the injector. If you see a small metal clip that looks like a staple, use a small flathead screwdriver to remove or depress the clip. Grasp the injector and work back and forth while pulling to remove from the fuel rail. The injector and rail will drip, so have shop towels ready.
PRO TIP:Before installing the new fuel injectors, dip the fuel injector tip (sprayer end) into a small amount ofengine oil. This will wet the seals, preventing leaks.
7.Press the injector into the rail until it stops. Attach the metal clip, if equipped.
8.Reattach the fuel rail. Line up all the injectors over their respective holes, then press each injector until they slide into place.
9.Bolt down fuel rail. Reattach fuel line. Plug in fuel injector electrical connections.
10.Reconnect battery.
11.Turn the key to the on position and wait 10 seconds before turning to engine start. This will allow the fuel pump to refill the lines and fuel rails before the engine cranks.
12.After the engine drops to the normal idle RPM, turn the engine off. Take a flashlight and check all the injectors for fuel leaks.
How important is replacing your fuel Injectors?
A leaking or plugged fuel injector causes the related cylinder to run richor lean, both of which can cause long-term problems that require extensive repairs.
In addition, your car’s performance will suffer and your Check Engine light will remain on until the repair is performed.
Is there a break-in period with my new fuel injectors?
Yes & No. All of our fuel injectors are ready to operate upon installation.
Starting the engine and letting it idle for a minimum of 20 minutes is the best thing to do after installing new injectors. This will push the aerated fuel out of the injector nozzle. Failure to do this may create a low/no-fuel condition, which could cause internal damage to the injectors. The new fuel injectors will perform great initially, and you will continue to see increased performance up to 1000-3000 miles as the injectors continue to break-in.
Can you upgrade fuel injectors?
Yes, a fuel injector upgrade is a great option to help add miles-per-gallon or restore lost power and torque in older or high-mileage engines. The first thing to know is "upgrading" does not mean changing the injector flow-rate. Upgrading means replacing old, worn, OEM fuel injectors with a new set of fuel injectors. This upgrade can improve the overall performance of an older engine.
There are 2 types of fuel injectors:
1. Diesel Fuel Injectors
Modern diesel fuel injectors are used to atomize and inject or spray diesel (which is heavier fuel than gasoline) directly into the combustion chamber of the diesel engine for compression ignition (no spark plugs).
Diesel fuel injectors require much higher injection pressure (up to 30,000 psi) than gasoline injectors as diesel is heavier than gasoline, and it takes much higher pressure to atomize the fuel.
2. Gasoline Fuel Injectors
Gasoline fuel injectors are used to inject or spray gasoline directly (GDI) or through intake manifold (multi-port) or throttle body into the combustion chamber for combustion which is ignited by spark.
The design of gasoline injectors varies by type… the newer GDI injectors use a multi holed nozzle, the multi-port and throttle body use a pointless style nozzle. Gasoline injection pressures are much lower than Diesel…3000 psi for GDI and 35 psi for Pinter style.
Clogged Fuel Injectors
It is not easy to diagnose a fuel injector as the symptoms it causes can be like a bad spark plug or ignition coil, meaning, one of the cylinders is not firing. If it is related to a clogged fuel injectorit is due to old fuel being run through the engine, resulting in residue getting stuck inside the injector or its filter basket. If a fuel injector becomes fully clogged it will have to be removed from the vehicle and be professionally cleaned, as additives and fuel tank introduced injection cleaners will not be able to clear the clog, as they cannot pass through at all.
Leaking Fuel Injectors
This can be an extremely dangerous situation. If the fuel injectors are leaking externally, you should not drive your vehicle. While a leaking injector will cause issues like that of a dirty one, you will often be able to smell gas or diesel under the hood or even spot a leak, depending on your make and model. Externally leaking injectors pose a fire risk and need to be completely replaced.
Fits Applications
With Fuel Return Line
Chevrolet Astro 1996-2001 V6 4.3L Conversion Kit to MFI
Chevrolet Astro 2002-2005 V6 4.3L
Chevrolet Blazer 1996-2000 V6 4.3L
Chevrolet Blazer 2001-2002 V6 4.3L Conversion Kit to MFI
Chevrolet Blazer 2003-2005 V6 4.3L
Chevrolet C1500 1996-1998 V6 4.3L Conversion Kit to MFI
Chevrolet Express 1500 1996-2002 V6 4.3L Conversion Kit to MFI
Chevrolet Express 1500 2003-2014 V6 4.3L
Chevrolet Express 2500 1996-2002 V6 4.3L Conversion Kit to MFI
Chevrolet Express 2500 2003-2005 V6 4.3L
Chevrolet K1500 1996-1998 V6 4.3L Conversion Kit to MFI
Chevrolet P30 1996-1999 V6 4.3L Conversion Kit to MFI
Chevrolet S10 1996-2002 V6 4.3L Conversion Kit to MFI
Chevrolet S10 2003-2004 V6 4.3L
Chevrolet Silverado 1500 1999-2001 V6 4.3L Conversion Kit to MFI
Chevrolet Silverado 1500 2002 V6 4.3L VIN: W, Conversion Kit to MFI
Chevrolet Silverado 1500 2002-2013 V6 4.3L 2002: VIN: X
GMC C1500 1996-1998 V6 4.3L Conversion Kit to MFI
GMC Jimmy 1996-2002 V6 4.3L Conversion Kit to MFI
GMC K1500 1996-1998 V6 4.3L Conversion Kit to MFI
GMC P3500 1996-1999 V6 4.3L Conversion Kit to MFI
GMC Safari 1996-2001 V6 4.3L Conversion Kit to MFI
GMC Safari 2002-2005 V6 4.3L
GMC Savana 1500 1996-2002 V6 4.3L Conversion Kit to MFI
GMC Savana 1500 2003-2013 V6 4.3L
GMC Savana 2500 1996-2002 V6 4.3L Conversion Kit to MFI
GMC Savana 2500 2003-2006 V6 4.3L
GMC Sierra 1500 1999-2002 V6 4.3L Conversion Kit to MFI. 2002: VIN: W
GMC Sierra 1500 2002-2013 V6 4.3L 2002: VIN: X
GMC Sonoma 1996-2002 V6 4.3L Conversion Kit to MFI
GMC Sonoma 2003-2004 V6 4.3L
Isuzu Hombre 1997-2000 V6 4.3L Conversion Kit to MFI
Oldsmobile Bravada 1996-2001 V6 4.3L Conversion Kit to MFI
Shipping WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3.Local pick up is not available.
4.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to offerding/buying.]
Payment 1.We accept multiple payment methods, such as PayPal, VISA, Master Card, etc..
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 7 days as sale ended or order might be delayed.
Returns 1.All of our brand new items come with a 60-Days money-back guarantee.
2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before offerding.
3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.
4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.
5.Shipping& handling cost are not refundable.
6.Man-made damage by abuse or wrong operation is not covered by this warranty.
7.No product liability insurance is assumed.
8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ]
Customer Services Q: How do I pay for my purchase?
A: MY store accepts PayPal, VISA, Master Card, etc..
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my "-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ]
response 1. We will leave a response once we get your payment.
2. If you are dissatisfied for any reason, please do contact us aresponse. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a response to all our customers.
3. If you are satisfied with the product you received, wish you can leave us a response.
Copyright of SCITOO-AutoParts . All rights reserved.
