Shown here is our BRAND NEW REPRODUCTION Single Groove water pump pulley for all big block engines that have no air conditioning. Works with or without power steering. Replacement for Chrysler part number 1821452. We make these from heavy duty steel, just like the factory Chrysler parts. Forget about scrounging up used and often damaged originals... we\'ve got great quality brand new reproductions at practically swap meet prices!And, FREE SHIPPING!! This item ships by Priority Mail, usually 2-3 day service.
Please note: The accessories Chrysler/Mopar used on the front of their engines for Air Conditioning cars vs. Non Air Conditioning cars are completely different. This unit is for the NON AIR CONDITIONING setup. It is designed to work with other pulleys, alternator brackets, spacers, power steering parts, etc that are also non air condtioning, to replicate the way the factory did it. We offer these items on also. If you try to mix and match some non air conditioning parts with other air conditioning parts, the belts will not line up and the pulleys will likely hit each other.
This is a very deep offset pulley, as designed from the factory. The rear edge of the V groove will sit very close to the four bolts which fasten the water pump to the water pump housing. The factory did not use washers on these bolts. If you try to use washers or aftermarket bolts with taller hex heads, the backside of the outer diameter of the pulley groove may slightly scrape the heads of these bolts. For this reason we recommend using regular hex bolts without washers for attaching the water pump to the water pump housing, just like the factory did. Measurements on this pulley are: Offset from the water pump mounting flange (the center of the pulley with the 4 mounting bolt holes) back to the center of the V groove (depth of the pulley) : 2 3/8\". Offset from the water pump mounting flange to the rear edge of the groove (OVERALL depth of the pulley): 2 11/16\". Pulley Diameter: 6 13/16\"PLEASE NOTE: Our reproduction Pulleys are stamped steel, just like the originals manufactured by Chrysler. As in all Stamped Steel Pulleys, including the originals by Chrysler, pulley concentricity (roundness) may vary 0.020 inch to 0.070 inch (up to approximately 1/16 inch). This does not affect the ability of the pulley to retain its belt throughout the power band of the engine. If you are concerned about this, we recommend upgrading to a fully machined style pulley, such as a billet aluminum style instead.Buy with confidence! 440 Source has been on since May 1st, 1999! We are the Big Block Mopar parts experts. We\'ve sold over 33 MILLION DOLLARS of Big Block Mopar parts, we know this engine backwards and forwards. Take a look at our web store for every big block part you could possibly need!
Keywords: Chrysler Corporation Mopar Dodge Plymouth 1969 69 1970 70 1971 71 1972 72 1973 73 1974 74 1975 75 1976 76 1977 77 1978 78 Dart Valiant Barracuda Cuda Challenger Demon Scamp GT GTS Polara Suburban Custom Sport Three Hundred Satellite & Sebring Plus, Belvedere I II III VIP Monaco GTX Super Bee Rallye Charger SE Coronet 440 500 Savoy Crestwood Aspen, Volare, Road Runner, Super Coupe, Super Pak, Duster, Cordoba, New Yorker, Gran Fury.
Charger Cuda GTX SuperBee RoadRunner Coronet R/T Satellite Belvedere Daytona SuperBird Dart Swinger GT Duster Demon Fury Polara Newport NewYorker Chrysler300 Monaco Valiant Scamp Signet Dodge Plymouth Mopar Chrysler
273, 318, 340, 360, 383, 413, 426 Wedge, 426 Hemi, 440 engines, blocks, crankshafts, heads, intakes for Chrysler, Dodge, Plymouth GTX, Road Runner, Charger R/T, Duster, Dart Sport, GT, GTS, Demon, Barracuda, \'Cuda, Challenger R/T, Coronet 500, R/T, Sport Satellite, Sport Fury, Belvedere, Superbird, Daytona Valiant Dart Barracuda Belvedere Coronet Charger Satellite Road Runner GTX R/T Superbee Cuda Challenger Plymouth Dodge Chrysler Imperial Dodge truck and Jensen Intercepter. Dodge Charger Roadrunner plymouth GTXSupercharged Turbocharged DFI ECU ECM High rise Race Drag fuel injection fuel injected mopar Chrysler blown
