Manufacturer
DIRECTED ELECTRONICS INC. [DEI]
VIPER / CLIFFORD / PYTHON
Compatible FCC ID#(s):
FCC ID: EZSDEI7141 EZSDE17141
Alternate Spellings
[ ALTERNATE SPELLINGS: EZSDEI7141 V/P/X]
Part #(s)
PART #:
RPN 7141V
INTERCHANGEABLE WITH:
7141V, 7141P
Dealer #(s)
7141V (Interchangeable Part #s): 7131 7131V 7131P 7131X 7141 7141V 7141P 7141X 7142 7142V 7142P 7142X 7151 7151V 7151P 7151X Part number on the remote is 7142V but replace 7142V, 7145V, 7146V, 7141V, 7131V, 7131P, 7131X, 7141, 7141V, 7141P, 7141X, 7142, 7142V, 7142P, 7142X, 7151, 7151V, 7151P, 7151X, remotes.
Button Count:
4: Lock, Unlock, Trunk Opener , Car Starter good for 2000ft range or 1/4 mile
Battery (installed):
2; CR2016
Frequency:
433 - 434 MHz
LED Light Color:
Blue
Circuit board #s:
#s on Chip on board:
Condition Notes:
Pre-Owned ready to program hole in back of CASE - SEE PHOTOS
Compatible Aftermarket Installed Systems:
Direct replacement for the following systems:
Arrow 5.1
Avantguard 5.1
Avital 4103
Clifford Matrix 12 12.2 12.5 70.5
Concept 470 650 MKII
Intelliguard 770
Python 460 502 702 902
Viper 100 HF
150 ESP
160 XV
210 HV
211 HV
300 HF
PC 300 HF (ESP)
300+ HF
330 V
350 HV RESPONDER 350
350+
500 HF
PC 500 HF (ESP)
550 HF
550 HF (ESP)
560 XV
571 XV
600 HF
PC 600 HF (ESP) 650 XV
671 XV
700 ESP
771 XV
PC 800 SHF
800 SHF ESP
850 XV
1000
1002
3002
Years: 3000
4103XV
5000
5002
Vss 5000
7900
Programming: Please note not all customers will be able to complete the programming on their own so if you are having trouble or unsure diagnostic programming is available at your local qualified automotive locksmith or car/audio shop.
Programming option #1:
1) Door. Open Door.
2) Key. Turn the key to the ON position.
3) Choose. Within 5 seconds press and release the Valet/Program button the number of times corresponding to selected channel listed below.
After you have selected the channel, press the Valet/Program button once more and hold it. The LED flashes the same number of times as the channel selected and the siren (if connected) chirps to confirm the selected channel. DO NOT release the Valet/Program button!
4) Transmit. While holding the Valet/Program button, press the button from the transmitter. The unit chirps (if horn or siren are connected) to confirm that the transmitter has been taught to the receiver.
5) Release. Now that the code is learned, you may release the Valet/Program button and remove the key.
CHANNEL NUMBER FUNCTION
7) ----------------------------------- AUTO-LEARN STANDARD CONFIGURATION
9) ---------------------------------- DELETE ALL TRANSMITTERS
Programming option #2:
1.IGNITION ON: Turn the ignition to the run position or start the engine.
2. ENTER PIN: Enter the factory preset PIN code 2 by pressing (*) on the Valet switch twice, then (gray square) on the Valet switch once.
Note: If the factory preset PIN has been changed, the new PIN must be entered.
3.HOLD/CHIRP/RELEASE: After entering the PIN code, press and Hold (*) on the Valet switch until a chirp is heard & the LED turns on, then release the button. You have now entered the feature selection position of the User Selectable Features grid.
4.COLUMN SELECT: Press (gray square) on the Valet switch the same number of times as the desired column. After a pause, the siren will chirp the same number of times as the selected column for confirmation.
5.FEATURE SELECT: Press (*) on the Valet switch the same number of times as the desired feature. The siren will chirp with each press. The feature can now be changed using the remote transmitter.
6.FEATURE CHANGE: Press (unlock/lock) on the transmitter. If the system chirps once, the feature has just turned off; if the system chirps twice, the feature has just turned on. If the feature has more than two settings, continue pressing (unlock/lock) on the transmitter to toggle through the settings.
You can advance to any feature in the same column by pressing (*) within 60 seconds; to program a feature in a different column, begin at step 4 within 60 seconds.
7.EXIT PROGRAMMING: To exit programming mode, turn the ignition off or wait 60 seconds without pressing the Valet switch. The siren will chirp 3 times to indicate programming mode has been exited.
AUTO-PROGRAM REMOTE:
Auto-learn remote to the system in the standard button configuration. Once you have entered the feature, press (unlock/lock) on the transmitter until you hear a confirmation indicating the new remote is learned.
