Set(4) 1.25\" Wheel Spacers 5x4.5\" to 5x5\" For Dodge Ford Lincoln Mazda Mercury For Sale - New and Used

Thread Size：1/2\'\'*20 Spacer Thickness: 1.25\"

Color：Black Number of Pieces: 4 />Dodge Dakota 1987-1990

Ford:
Ford Crown Victoria 1992-2011
Ford Edge 2007-2014
Ford Explorer 1991-2014
Ford Explorer Sport Trac 2001-2005 & 2007-2010
Ford Five Hundred 2005-2007
Ford Flex 2009-2014
Ford Freestar 2004-2007
Ford Mustang 1994-2014
Ford Ranger 1983-2011

Jeep:
Jeep Cherokee 1984-2001
Jeep Comanche 1986-1992
Jeep Compass 2007-2014
Jeep Grand Cherokee 1993-1998
Jeep Liberty 2002-2012
Jeep Patriot 2007-2014
Jeep TJ 1997-2006
Jeep Wrangler 1987-2006

Lincoln:
Lincoln Town Car 1982-2011

Mazda:
Mazda B2500 1998-2001
Mazda B3000 1994-2008
Mazda B4000 1994-2010
Mazda Navajo 1993-1994

Mercury:
Mercury Mountaineer fitment compatibility is only a guide, please make sure that these are the correct application for your vehicle.

Important Notes

Professional Installation is highly recommended!!

Please check if you have received and prepared all required parts before installation.

Before Action

STEP-1Vehicle bolt pattern check

Confirm your vehicle bolt pattern according to the figure below.

Let\'s take the 5-lug wheel spacer as an example, if the length of segment as measured in the picture is 5.5”, and as there are 5 lugs, then the bolt pattern is 5x5.5\". Now you should be able to determine what kind of bolt patterns you need.

STEP-2 Measurement
Measure the diameter of the center bore of the wheel spacers, make sure that it is greater than the axle diameter.

STEP-3 Check
Check the thread size, which is often ignored by customers when placing the order.
TIPS: install the supplied lug nuts or bolts on the hub only by hand (do not install the wheel at this time). It might be the wrong thread size for your vehicle when you feel resistance during the process, and please con:act the tire seller or manufacturer for further suggestions.

Installation NOTICE

1.Take off wheel nuts and bolts.

2.Remove old washers. Please clean the dust on the hub before installation. (Dust or oil may caused vibration)

3.Place wheel spacers over alxe hub and make sure it sits firmly.

4.Tighten nuts in crissscross pattern.

5.Use thread locker to ensure the nuts secure enough and place the wheel back on

Note:t is possible that your existing lug nut studs can be longer than the adapter itself, you may need to alter your existing studs if the adapters do not sit flush with the wheels. If the studs are longer than the adapter, and the wheels do not have a hollow spot in them, you may need to grind, or cut your existing lugs if you choose not to purchase shorter studs. Otherwise, the adapter bolt can、work as normal and will -r-atlv shorten the bolt\'s workinq life and bring danger to you.

Maintenance TIPS

Please check all lug nuts and bolts of the adapters after the first 50 -100 miles. They may get loose after long time running. Make sure you will recheck them every 3000 - 5000 miles and screw tight.

IMPORTANT SAFETY INFORMATION

Not modify wheel spacer and remove factory installed studs on wheel spacer/adapter.

Not use multiple spacer over a single wheel.

·No returns are accepted without an RMA number.

· Full Refund is valid within 60 days after the date delivered

·Refund will be given as money back(only order value) or replacement

·The money less the freight cost will be refunded due to their own fault

·Item must be returned in original packing same as reached

·Buyers are responsible for the return shipping cost.

Warranty·Buyers pay return and replacement shipping cost·We will not refund any labor costCustomer Service·Any question will be replied within 24 hours except the weekend and holiday.response
• We highly appreciate that you can contact with us before you leaving Negative response,opening return or case. It is because leaving Negative response,opening return or case is not a good way to resolve problem. We will offer proper arrangement and help to resolve any problem as soon as possible.



---