Brand NEWBlower Motor Rear Fits 2009 10 11 12 13-2019 Dodge Journey A/C Heater Blower Motor 68038189AA Brand NEWBlower Motor
NEW, not remanufacturedor rebuilt DIRECTREPLACEMENT Built to strict quality control standards HIGH QUALITY - Top quality materials which provide maximum strength and durability 1YEAR WARRANTY-This item is backed by a 1Year Warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge (excludes shipping charges) for the original purchaser. 100% tested prior to leaving the factory The blower motor can be installed easily with no special tools required and just by removing a few screws under the passenger side dash of your vehicle. Simply remove the old blower motor and put the new one in. It is also a advisable to replace your blower motor relay/resistor with a new one when you replace your blower motor.What Are Signs Your Blower Motor Needs to Be Replaced?
- Poor or Airflow from Air Vents
- No Airflow At All From Vents
- Skyrocketing Energy Bills
- Strange Noises When You Turn on the Heat
- Overheating Blower / Weird Smells
Fitting for the following years and models:
Step 1
Disconnect the ground cable from the negative battery terminal. Loosen the retaining bolt using a wrench. Pull the clamp off the terminal.
Step 2
Locate the blower motor. On most vehicles, it will be located inside the engine bay along the firewall on the passenger side of the vehicle. On some vehicles, it may be located inside the passenger compartment, below the dash on the passenger side of the vehicle.
Step 3
Pull the wiring connector or connectors off the blower motor, using your hand. In most cases there will be one plastic connector. If there are more than one, use masking tape and a marker to label them for reassembly,
Step 4
Using a socket, unscrew the screws that secure the blower motor to the heater case or firewall.
Step 5
Pull the blower motor and fan blades from the vehicle as an assembly.
Step 6
Unscrew the nut that secures the fan blades to the motor, using a socket.
Step 7
Pull the fan blades away from the motor.
Installing the Blower Motor
Step 1
Drop the fan blades into position on the new motor.
Step 2
Screw on the nut that secures the fan blades to the motor.
Step 3
Slide the motor/fan blade assembly into position in the heater case or firewall.
Step 4
Screw in the screws that secure the blower motor to the heater case or firewall.
Step 5
Press the plastic wiring connector onto the back of the blower motor.
Step 6
Reconnect the ground cable to the negative battery terminal. Slide the clamp over the terminal and tighten the retaining bolt with a wrench.
Step 7
Test for proper
Please compare your parts against pictures to ensure this part fits your vehicle Please confirm your old part number matches up with one of the part numbers above Professional installation is highly recommended (No Instruction Included) For any needs please contact us. Rear Fits 2009 10 11 12 13-2019 Dodge Journey A/C Heater Blower Motor 68038189AA
Brand NEWBlower Motor
NEW, not remanufacturedor rebuilt DIRECTREPLACEMENT Built to strict quality control standards HIGH QUALITY - Top quality materials which provide maximum strength and durability 1YEAR WARRANTY-This item is backed by a 1Year Warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge (excludes shipping charges) for the original purchaser. 100% tested prior to leaving the factory The blower motor can be installed easily with no special tools required and just by removing a few screws under the passenger side dash of your vehicle. Simply remove the old blower motor and put the new one in. It is also a advisable to replace your blower motor relay/resistor with a new one when you replace your blower motor.What Are Signs Your Blower Motor Needs to Be Replaced?
- Poor or Airflow from Air Vents
- No Airflow At All From Vents
- Skyrocketing Energy Bills
- Strange Noises When You Turn on the Heat
- Overheating Blower / Weird Smells
Fitting for the following years and models:
Step 1
Disconnect the ground cable from the negative battery terminal. Loosen the retaining bolt using a wrench. Pull the clamp off the terminal.
Step 2
Locate the blower motor. On most vehicles, it will be located inside the engine bay along the firewall on the passenger side of the vehicle. On some vehicles, it may be located inside the passenger compartment, below the dash on the passenger side of the vehicle.
Step 3
Pull the wiring connector or connectors off the blower motor, using your hand. In most cases there will be one plastic connector. If there are more than one, use masking tape and a marker to label them for reassembly,
Step 4
Using a socket, unscrew the screws that secure the blower motor to the heater case or firewall.
Step 5
Pull the blower motor and fan blades from the vehicle as an assembly.
Step 6
Unscrew the nut that secures the fan blades to the motor, using a socket.
Step 7
Pull the fan blades away from the motor.
Installing the Blower Motor
Step 1
Drop the fan blades into position on the new motor.
Step 2
Screw on the nut that secures the fan blades to the motor.
Step 3
Slide the motor/fan blade assembly into position in the heater case or firewall.
Step 4
Screw in the screws that secure the blower motor to the heater case or firewall.
Step 5
Press the plastic wiring connector onto the back of the blower motor.
Step 6
Reconnect the ground cable to the negative battery terminal. Slide the clamp over the terminal and tighten the retaining bolt with a wrench.
Step 7
Test for proper
Please compare your parts against pictures to ensure this part fits your vehicle Please confirm your old part number matches up with one of the part numbers above Professional installation is highly recommended (No Instruction Included) For any needs please contact us. Item SpecificsBrand :SCITOOManufacturer Part Number :CB151462S01Material :ABS PlasticManufacturer Warranty :1 YearPlacement on Vehicle :RearPackage include :1 x Blower motor fan w/ fan cageFitment Type :Direct ReplacementInterchange Part Number :68038189AA,furnace blower motorShaft Type :Single ShaftProduct Name :Heater A/C AC Blower Motor w/ Fan CageOther Part Number :68038189AASuperseded Part Number :replacing blower motor,heater blower motorTypes : HVAC Blower MotorWorking Voltage :12VTerminals Type : BladeMaterial :Plastic & Metal
Shipping
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3.Local pick up is not available.
4.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to offerding/buying.]
Payment
[We only accept payment through PayPal. You can open a Paypal account at www.paypal.com.]
Returns
1.All of our brand new items come with a 60-Days money-back guarantee.
2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before offerding.
3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.
4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.
5.Shipping& handling cost are not refundable.
6.Man-made damage by abuse or wrong operation is not covered by this warranty.
7.No product liability insurance is assumed.
8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ]
Customer Services
Q: How do I pay for my purchase?
A: MY store accepts PayPal.
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my "-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ]
response
1. We will leave positive response once we get your payment.
2. If you are dissatisfied for any reason, please do contact us before you leaving a response. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a response to all our customers.
3. If you are satisfied with the product you received, wish you can leave us a response.
New List Item Driver Side Mirror Fits For 2008-2014 DODGE AVENGER Light Textured Power Heated USD 44.19 For BMW 135i 3.0L 2008-2010 BMW 335i 3.0L 2007-2010 Turbocharger 49131-07041 USD 215.98 2X For 2009-2010 Ford Flex Lincoln MKS HVAC Heater Blend Door Actuator Temp USD 22.87 For BMW 135i E82 E88 335i E90 E91 E92 E93 N54 3.0L Driver & Passenger Side Turbo USD 432.28 For BMW 335i E90 E91 E92 E93 Engine N54B30 3.0L 2006-2011 Turbocharger Set USD 427.98 Shop CategoryStore Home A/C Expansion Valve ABS Wheel Speed Sensor AC Compressor AC Compressor Control Valve+A AC Condenser & Radiator◈AC Condenser◈AC Condenser & Radiator◈Radiator Adjustable Control /Camber Arm Air Cleaner Filter Box Air Diesel Heater Air Dryer Air suspension valves solenoid Air suspensions Alternators ATV Brake Caliper ATV Brake Master Cylinder ATV Ignition Switch ATV Rear Wheel Axle ATV Tires Auto parts◈Blower Motor◈Coilover◈complete struts◈CV Axle◈Fuel Pump Assembly◈Ignition Coil◈Key Case◈Starter◈strut/absorber shock◈Struts/Absorbers Shocks◈Towing Mirrors◈Trunk Floor Mats◈Window Switch ball joint Ballast module Bed Step Blower Motor & Resistor Brake Oil Hose Brake Pads & Rotors◈Brake Pad Sensor◈Brake Pads◈Brake Rotors◈Brake Rotors and Pads Brake System Parts◈Brake Calipers◈Brake Drums & Brake Shoes◈Brake Pads & Brake Shoes Bumper C Notch & Flip Kit Camshaft & Crankshaft Camshaft Position Sensor Car Antenna Car Carburetor Car Cover Car Seat Cover Car Tools Cargo Cover CDI BOX Consoles & Parts Control Arms & Parts Cooling Fan Cooling Fan Clutch Crankcase Vent Valve Crankshaft Position Sensor CV axle+Brake Pads/Rotors Cylinder Head Gasket Sets Cylinder Piston Gasket Kit Cylinder Piston Kit dash cover Dipstick Door check stop Door handle Door Lock Actuator Driveshaft Electric Water Pump Engine Mount Evaporators Fastener Fender Flares fog lights Foot Rest Pedal Front Bumper LipHot Item 2pc 3157 4114 4157 LED DRL Driving Daytime Running Light Bulbs 12SMD 6000K White USD 8.39 12V Universal Fuel Pump Gas Diesel Inline Low Pressure HEP-02A BHEP-02A USD 11.59 Alternator for 110Amp Chrome Street Rod GM 305 350 BBC SBC 1 Wire Self Exciting USD 68.39 Inline Universal High Pressure Fuel Pump With Installation Kit 0580464070 USD 20.95 Fuel Pump for Chevy S10 GMC Sonoma Hombre 4.3L 97-02 for Isuzu Hombre 4.3L 97-20 USD 33.39 Picture
Rear Fits 2009 10 11 12 13-2019 Dodge Journey A/C Heater Blower Motor 68038189AA
Brand NEWBlower Motor
NEW, not remanufacturedor rebuilt DIRECTREPLACEMENT Built to strict quality control standards HIGH QUALITY - Top quality materials which provide maximum strength and durability 1YEAR WARRANTY-This item is backed by a 1Year Warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge (excludes shipping charges) for the original purchaser. 100% tested prior to leaving the factory The blower motor can be installed easily with no special tools required and just by removing a few screws under the passenger side dash of your vehicle. Simply remove the old blower motor and put the new one in. It is also a advisable to replace your blower motor relay/resistor with a new one when you replace your blower motor.What Are Signs Your Blower Motor Needs to Be Replaced?
- Poor or Airflow from Air Vents
- No Airflow At All From Vents
- Skyrocketing Energy Bills
- Strange Noises When You Turn on the Heat
- Overheating Blower / Weird Smells
Fitting for the following years and models:
Step 1
Disconnect the ground cable from the negative battery terminal. Loosen the retaining bolt using a wrench. Pull the clamp off the terminal.
Step 2
Locate the blower motor. On most vehicles, it will be located inside the engine bay along the firewall on the passenger side of the vehicle. On some vehicles, it may be located inside the passenger compartment, below the dash on the passenger side of the vehicle.
Step 3
Pull the wiring connector or connectors off the blower motor, using your hand. In most cases there will be one plastic connector. If there are more than one, use masking tape and a marker to label them for reassembly,
Step 4
Using a socket, unscrew the screws that secure the blower motor to the heater case or firewall.
Step 5
Pull the blower motor and fan blades from the vehicle as an assembly.
Step 6
Unscrew the nut that secures the fan blades to the motor, using a socket.
Step 7
Pull the fan blades away from the motor.
Installing the Blower Motor
Step 1
Drop the fan blades into position on the new motor.
Step 2
Screw on the nut that secures the fan blades to the motor.
Step 3
Slide the motor/fan blade assembly into position in the heater case or firewall.
Step 4
Screw in the screws that secure the blower motor to the heater case or firewall.
Step 5
Press the plastic wiring connector onto the back of the blower motor.
Step 6
Reconnect the ground cable to the negative battery terminal. Slide the clamp over the terminal and tighten the retaining bolt with a wrench.
Step 7
Test for proper
Please compare your parts against pictures to ensure this part fits your vehicle Please confirm your old part number matches up with one of the part numbers above Professional installation is highly recommended (No Instruction Included) For any needs please contact us. Item SpecificsBrand :SCITOOManufacturer Part Number :CB151462S01Material :ABS PlasticManufacturer Warranty :1 YearPlacement on Vehicle :RearPackage include :1 x Blower motor fan w/ fan cageFitment Type :Direct ReplacementInterchange Part Number :68038189AA,furnace blower motorShaft Type :Single ShaftProduct Name :Heater A/C AC Blower Motor w/ Fan CageOther Part Number :68038189AASuperseded Part Number :replacing blower motor,heater blower motorTypes : HVAC Blower MotorWorking Voltage :12VTerminals Type : BladeMaterial :Plastic & Metal
ShippingPaymentReturnsCustomer Servicesresponse
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3.Local pick up is not available.
4.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to offerding/buying.]
[We only accept payment through PayPal. You can open a Paypal account at www.paypal.com.]
1.All of our brand new items come with a 60-Days money-back guarantee.
2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before offerding.
3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.
4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.
5.Shipping& handling cost are not refundable.
6.Man-made damage by abuse or wrong operation is not covered by this warranty.
7.No product liability insurance is assumed.
8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ]
Q: How do I pay for my purchase?
A: MY store accepts PayPal.
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my "-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ]
1. We will leave positive response once we get your payment.
2. If you are dissatisfied for any reason, please do contact us before you leaving a response. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a response to all our customers.
3. If you are satisfied with the product you received, wish you can leave us a response.
