REPLACING THETHROTTLE BODYASSEMBLYUnder some circumstances, it might be necessary to removethe throttle bodyassembly. Sometimes it may be to thoroughlyclean the inlet and throttle blade,but more often it will be toreplace it. The procedure is pretty straightforward.Q:How to tell if you need a new throttle body For Chevy Equinox 2.4L 10-11 Throttle Body w/ Throttle Position Sensor 217-3428
REPLACING THETHROTTLE BODYASSEMBLY
Under some circumstances, it might be necessary to removethe throttle body
assembly. Sometimes it may be to thoroughlyclean the inlet and throttle blade,
but more often it will be toreplace it. The procedure is pretty straightforward.
Q:How to tell if you need a new throttle body
A:If you find that your car idles quicker than usual, that may mean that the throttle body is sticking open. If your check engine light comes on and you find that you can’t get the car to accelerate above a certain rpm, the ECU has put you in limp mode. This means that there is something wrong with the drive-by-wire system. The most dangerous indicator is if the throttle sticks while driving and you can’t get the car to stop accelerating. If that ever happens, put the car in neutral and turn the key back one click and coast to the side of the road.
REMOVAL
1. Disconnect the ground cable from battery.
2. Lift up the vehicle.Remove the under cover.
3. Remove the clip (A), and loosen the clamps (B) and (C) securing the air intake boot.
4. Remove the air intake boot from the air cleaner case (rear) and throttle body, and move the air intake boot aside so that it does not interfere with the work.
5.Disconnect the connectors (A) from the throttle position sensor.
6.Disconnect the preheater hose (B) from the throttle body.
7.Remove the throttle body from the intake in the reverse order of installing the new assembly, inspect the intake-manifold-to-throttle-body gasket for damage. If it is damaged,it must be replaced.
If it is in good condition, it can be reused.
WARNING:
DO NOT place fingers in or around the throttle bodyplate. If the throttle body is energized, the throttle plate couldmove causing personal injury. Always disconnect the negativebattery cable prior to servicing the throttle body.
CAUTION:
DO NOT move the throttle plate while power isconnected to the throttle body. This may cause fault codes to set.
Q:Is there anything that has to be done after installing the replacement throttle body
A:A relearncalibration procedure is necessary after installation of replacement throttle body
Q:What is throttle body relearn
A:Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc.
RelearnA MECHANICALLY CONTROLLED THROTTLEBODY
1. Remove terminals from the battery for 15 minutes.
2. Start the engine. Let it idle for 10 minutes. Remember not to switch on any additional consumers.
3. Stop the engine for about 10 seconds. Start it again.
4. Wait until the power unit warms up to the operating temperature. After that, you can start using the vehicle.
Take notice:you might need to drive 150–200 km until the idling stabilises.
RelearnAN ELECTRONICALLY CONTROLLED THROTTLEBODY
The readjustment process might vary in different vehicles. Therefore, before you start the procedure, consult the vehicle manual for the exact step sequence.
The general algorithm is as follows:
1. Study procedure and try to remember it. You’ll have to act quickly so you won’t have time to check the details.
2. Start the engine. Warm it up to the working temperature.Stop it for 10 seconds.
3. Switch on the ignition for 3 seconds.
4. Press the accelerator pedal quickly for 5 times. One depression should take one second.
5. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds.
6. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds.
7. Release the gas pedal and start the engine.
Q:HOW TO PREVENT THE THROTTLE BODY FROM GETTING DIRTY
A:1. Use only high-quality fuel. Otherwise, impurities and contaminants will get inside the engine causing the rapid formation of carbon deposits on the throttle body. For the same reason, you shouldn’t neglect the fuel filter replacement. It is recommended to flush the fuel tank from time to time.
2. Replace the air filter on time. Always make sure that the intake system is air-tight. This simple check prevents unfiltered air from being sucked into the intake system in places where its components are not connected tightly.
3. Always make sure that the crankcase ventilation system is fault-free. Its malfunctions cause a fast formation of oily deposits on elements of the throttle body.
Fits the Following Vehicles:
Chevrolet Equinox 2.4L 2010-2011
Item SpecificsBrand Autoparts_UnionManufacturer Part Number US98104N63739Type Throttle BodyConnector Quantity 1Items Included Throttle Position SensorFeatures ElectronicOE/OEM Part Number 977-779Connector Type BladeColor SilverFuel Type GasolinePerformance Part YesBore Diameter 65mmManufacturer Warranty 1 YearUniversal Fitment NoMaterial AluminumVintage Part NoInterchange Part Number 12615516Superseded Part Number Electrical Throttle Body Assembly with SensorFitment Type Direct ReplacementThrottle Body Actuation Type ElectricalTerminal QTY 6Gaskets Included NoWeight 3 LBPlacement on Vehicle FrontMount Hole Quantity 4Fuel System Type FIPackaging Type BoxModified Item NoCustom Bundle NoMounting Hardware Included NoHousing Length (in) 6-3/16Housing Width (in) 5-9/16Main Port Inside Diameter(in) 2-5/8Air Intake Port Maximum Diameter (in) 2-13/16Throttle Plate Diameter (in) 2-9/16OE 977-779Vintage Car Part No
Payment We accept Paypal only for the payment, and all orders should be paid through sale, please do not pay directly to our Paypal account.Paypal allows to pay by Credit Card, Direct Debit, VISA, eCheck, or other methods, please kindly check Paypal for more information.For multiple purchases, please add items to your shopping cart and pay once for entire order.Shipping
All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
We do not ship toP.O. Boxes, APO/FPO orMilitary Mail Box.
We only ship to Paypal confirmed address, please make sure that the address is correct before you check out.
Returns
All of our brand new items come with a 60-Days money-back guarantee.
If you are not satisfied with your purchase, you can return the item with original packaging back to us for full refund, not any re-stock fee. The return cost should be paid by seller.
Kindly contact us forreturn instructionbefore returning.
If you receive any wrong items, or damage during the transportation or defect items, we will accept the return and pay the return freight. Please noted that the return cost should be prepaid by buyer, we will issue the refund of return cost to buyer after inspecting the faulty item.
The full refund or replacement will be available for all faulty items, including the original shipping cost.
Please kindly contact us before return, ourrepresentatives will send you the detailed return instruction.
The guarantee will be only for the cost of the item, we will not responsible for installation or other fees likelabor expenses, towing expenses, additional repair expenses or other related expenses.
Contact Us
We fully understand how challenging it is to be a successful transaction. If you are not 100% satisfied with your purchase, please do not hesitate to tell us, our sales representatives will try the best to make you happy. Customer satisfaction is our priority consideration!
Warning
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Best Sales Throttle Body with Actuator for Honda Accord 2006-2007 Civic CR-V Acura CSX 2.4L USD 70.50 Throttle Body for Chevrolet Cobalt Malibu HHR Pontiac G5 Saturn Ion Vue 2.2L New USD 61.47 For 2005-2006 Ford Five Hundred Mercury Montego 3.0L Throttle Body w/Pipes USD 62.90 Throttle Body For 2012-2019 Nissan Versa 1.6L 2014-2019 Nissan Versa Note USD 64.84 Electronic Throttle Body Assembly for Mini Cooper 07-15 Countryman Paceman 1.6L USD 69.46 Newly Listed Turbo Turbocharger Fits 2010 2011-2015 Kia Optima Sportage Theta 1pc 28231-2G410 USD 292.99 Air Blend Door Actuator for Chevrolet Impala 04-13 Corvette 05-13 604-108 USD 10.29 Air Blend Door Actuator for Chevrolet Impala 04-13 Corvette 05-13 604-108 USD 10.29 For Volvo S60 V70 2007-2009 Fuel Pump Assembly with Sending Unit 30761747 USD 156.89 Headlights Assembly For 2005-2007 Ford F250 F350 F450 Black Left + Right Side USD 80.99 Terms & ContactPayment PolicyShipping PolicyReturn PolicyFAQAbout Us For Chevy Equinox 2.4L 10-11 Throttle Body w/ Throttle Position Sensor 217-3428
REPLACING THETHROTTLE BODYASSEMBLY
Under some circumstances, it might be necessary to removethe throttle body
assembly. Sometimes it may be to thoroughlyclean the inlet and throttle blade,
but more often it will be toreplace it. The procedure is pretty straightforward.
Q:How to tell if you need a new throttle body
A:If you find that your car idles quicker than usual, that may mean that the throttle body is sticking open. If your check engine light comes on and you find that you can’t get the car to accelerate above a certain rpm, the ECU has put you in limp mode. This means that there is something wrong with the drive-by-wire system. The most dangerous indicator is if the throttle sticks while driving and you can’t get the car to stop accelerating. If that ever happens, put the car in neutral and turn the key back one click and coast to the side of the road.
REMOVAL
1. Disconnect the ground cable from battery.
2. Lift up the vehicle.Remove the under cover.
3. Remove the clip (A), and loosen the clamps (B) and (C) securing the air intake boot.
4. Remove the air intake boot from the air cleaner case (rear) and throttle body, and move the air intake boot aside so that it does not interfere with the work.
5.Disconnect the connectors (A) from the throttle position sensor.
6.Disconnect the preheater hose (B) from the throttle body.
7.Remove the throttle body from the intake in the reverse order of installing the new assembly, inspect the intake-manifold-to-throttle-body gasket for damage. If it is damaged,it must be replaced.
If it is in good condition, it can be reused.
WARNING:
DO NOT place fingers in or around the throttle bodyplate. If the throttle body is energized, the throttle plate couldmove causing personal injury. Always disconnect the negativebattery cable prior to servicing the throttle body.
CAUTION:
DO NOT move the throttle plate while power isconnected to the throttle body. This may cause fault codes to set.
Q:Is there anything that has to be done after installing the replacement throttle body
A:A relearncalibration procedure is necessary after installation of replacement throttle body
Q:What is throttle body relearn
A:Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc.
RelearnA MECHANICALLY CONTROLLED THROTTLEBODY
1. Remove terminals from the battery for 15 minutes.
2. Start the engine. Let it idle for 10 minutes. Remember not to switch on any additional consumers.
3. Stop the engine for about 10 seconds. Start it again.
4. Wait until the power unit warms up to the operating temperature. After that, you can start using the vehicle.
Take notice:you might need to drive 150–200 km until the idling stabilises.
RelearnAN ELECTRONICALLY CONTROLLED THROTTLEBODY
The readjustment process might vary in different vehicles. Therefore, before you start the procedure, consult the vehicle manual for the exact step sequence.
The general algorithm is as follows:
1. Study procedure and try to remember it. You’ll have to act quickly so you won’t have time to check the details.
2. Start the engine. Warm it up to the working temperature.Stop it for 10 seconds.
3. Switch on the ignition for 3 seconds.
4. Press the accelerator pedal quickly for 5 times. One depression should take one second.
5. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds.
6. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds.
7. Release the gas pedal and start the engine.
Q:HOW TO PREVENT THE THROTTLE BODY FROM GETTING DIRTY
A:1. Use only high-quality fuel. Otherwise, impurities and contaminants will get inside the engine causing the rapid formation of carbon deposits on the throttle body. For the same reason, you shouldn’t neglect the fuel filter replacement. It is recommended to flush the fuel tank from time to time.
2. Replace the air filter on time. Always make sure that the intake system is air-tight. This simple check prevents unfiltered air from being sucked into the intake system in places where its components are not connected tightly.
3. Always make sure that the crankcase ventilation system is fault-free. Its malfunctions cause a fast formation of oily deposits on elements of the throttle body.
Fits the Following Vehicles:
Chevrolet Equinox 2.4L 2010-2011
Item SpecificsBrand :Autoparts_UnionManufacturer Part Number :US98104N63739Type :Throttle BodyConnector Quantity :1Items Included :Throttle Position SensorFeatures :ElectronicOE/OEM Part Number :977-779Connector Type :BladeColor :SilverFuel Type :GasolinePerformance Part :YesBore Diameter :65mmManufacturer Warranty :1 YearUniversal Fitment :NoMaterial :AluminumVintage Part :NoInterchange Part Number :12615516Superseded Part Number :Electrical Throttle Body Assembly with SensorFitment Type :Direct ReplacementThrottle Body Actuation Type :ElectricalTerminal QTY :6Gaskets Included :NoWeight :3 LBPlacement on Vehicle :FrontMount Hole Quantity :4Fuel System Type :FIPackaging Type :BoxModified Item :NoCustom Bundle :NoMounting Hardware Included :NoHousing Length (in) :6-3/16Housing Width (in) :5-9/16Main Port Inside Diameter(in) :2-5/8Air Intake Port Maximum Diameter (in) :2-13/16Throttle Plate Diameter (in) :2-9/16OE :977-779Vintage Car Part :No
PaymentShippingReturnsContact UsWarning We accept Paypal only for the payment, and all orders should be paid through sale, please do not pay directly to our Paypal account.Paypal allows to pay by Credit Card, Direct Debit, VISA, eCheck, or other methods, please kindly check Paypal for more information.For multiple purchases, please add items to your shopping cart and pay once for entire order.
All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
We do not ship toP.O. Boxes, APO/FPO orMilitary Mail Box.
We only ship to Paypal confirmed address, please make sure that the address is correct before you check out.
All of our brand new items come with a 60-Days money-back guarantee.
If you are not satisfied with your purchase, you can return the item with original packaging back to us for full refund, not any re-stock fee. The return cost should be paid by seller.
Kindly contact us forreturn instructionbefore returning.
If you receive any wrong items, or damage during the transportation or defect items, we will accept the return and pay the return freight. Please noted that the return cost should be prepaid by buyer, we will issue the refund of return cost to buyer after inspecting the faulty item.
The full refund or replacement will be available for all faulty items, including the original shipping cost.
Please kindly contact us before return, ourrepresentatives will send you the detailed return instruction.
The guarantee will be only for the cost of the item, we will not responsible for installation or other fees likelabor expenses, towing expenses, additional repair expenses or other related expenses.
We fully understand how challenging it is to be a successful transaction. If you are not 100% satisfied with your purchase, please do not hesitate to tell us, our sales representatives will try the best to make you happy. Customer satisfaction is our priority consideration!
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
All rights reserved.
