4PCS 5x120mm Wheel Spacers w/ 20 Bolts For BMW M2 M4 440i 320i 340i 328d 650i For Sale - New and Used

-4 x wheel spacers w/ 20 Bolts
-2 x lubricating oil

Important Notes

Professional Installation is highly recommended!!

Please check if you have received and prepared all required parts before installation.

Before Action

STEP-1Vehicle bolt pattern check

Confirm your vehicle bolt pattern according to the figure below.

Let's take the 5-lug wheel spacer as an example, if the length of segment as measured in the picture is 5.5”, and as there are 5 lugs, then the bolt pattern is 5x5.5". Now you should be able to determine what kind of bolt patterns you need.

STEP-2 Measurement
Measure the diameter of the center bore of the wheel spacers, make sure that it is greater than the axle diameter.

STEP-3 Check
Check the thread size, which is often ignored by customers when placing the order.
TIPS: install the supplied lug nuts or bolts on the hub only by hand (do not install the wheel at this time). It might be the wrong thread size for your vehicle when you feel resistance during the process, and please con:act the tire seller or manufacturer for further suggestions.

Installation NOTICE

1.Take off wheel nuts and bolts.

2.Remove old washers. Please clean the dust on the hub before installation. (Dust or oil may caused vibration)

3.Place wheel spacers over alxe hub and make sure it sits firmly.

4.Tighten nuts in crissscross pattern.

5.Use thread locker to ensure the nuts secure enough and place the wheel back on

Note:t is possible that your existing lug nut studs can be longer than the adapter itself, you may need to alter your existing studs if the adapters do not sit flush with the wheels. If the studs are longer than the adapter, and the wheels do not have a hollow spot in them, you may need to grind, or cut your existing lugs if you choose not to purchase shorter studs. Otherwise, the adapter bolt can、work as normal and will -r-atlv shorten the bolt's workinq life and bring danger to you.

Maintenance TIPS

Please check all lug nuts and bolts of the adapters after the first 50 -100 miles. They may get loose after long time running. Make sure you will recheck them every 3000 - 5000 miles and screw tight.

IMPORTANT SAFETY INFORMATION

Not modify wheel spacer and remove factory installed studs on wheel spacer/adapter.

Not use multiple spacer over a single wheel.

• SHOP
• CONTACT
• Shock Struts
• Fan
• Fuel Pump
• Exhaust Manifold
• Intake Manifold
• Tool
• Mirror
• Air Hose
• VVT
• Wheel Hub Bearing
• Valve Cover
• Ignition Colis
• Fog Light
• EGR
• Truck Cover
• Tail Light
• Roof Rack Cross Bar
• Window Regulator
• Door Handle
• Blower Motor
• Sun Visor
• Mass Air Flow Meter Sensor
• Nerf Bar
• Fuel Filler Gas Cap
• Floor Mats
• Oxygen Sensor
• Cup Holder
• Control Arm
• Water Pump
• Power Steering Rack Pinion
• Fuel injectors
• Oil Cooler
• Tire Pressure Sensor
• Nox Sensor
• Window Switch
• Package Includes

  
  -4 x wheel spacers w/ 20 Bolts
  -2 x lubricating oil

  Important Notes

  Professional Installation is highly recommended!!

  Please check if you have received and prepared all required parts before installation.

  Before Action

  
  STEP-1Vehicle bolt pattern check

  Confirm your vehicle bolt pattern according to the figure below.

  Let's take the 5-lug wheel spacer as an example, if the length of segment as measured in the picture is 5.5”, and as there are 5 lugs, then the bolt pattern is 5x5.5". Now you should be able to determine what kind of bolt patterns you need.

  STEP-2 Measurement
  Measure the diameter of the center bore of the wheel spacers, make sure that it is greater than the axle diameter.

  STEP-3 Check
  Check the thread size, which is often ignored by customers when placing the order.
  TIPS: install the supplied lug nuts or bolts on the hub only by hand (do not install the wheel at this time). It might be the wrong thread size for your vehicle when you feel resistance during the process, and please con:act the tire seller or manufacturer for further suggestions.

  Installation NOTICE

  
  1.Take off wheel nuts and bolts.

  2.Remove old washers. Please clean the dust on the hub before installation. (Dust or oil may caused vibration)

  3.Place wheel spacers over alxe hub and make sure it sits firmly.

  4.Tighten nuts in crissscross pattern.

  5.Use thread locker to ensure the nuts secure enough and place the wheel back on

  
  Note:t is possible that your existing lug nut studs can be longer than the adapter itself, you may need to alter your existing studs if the adapters do not sit flush with the wheels. If the studs are longer than the adapter, and the wheels do not have a hollow spot in them, you may need to grind, or cut your existing lugs if you choose not to purchase shorter studs. Otherwise, the adapter bolt can、work as normal and will -r-atlv shorten the bolt's workinq life and bring danger to you.

  Maintenance TIPS

  
  Please check all lug nuts and bolts of the adapters after the first 50 -100 miles. They may get loose after long time running. Make sure you will recheck them every 3000 - 5000 miles and screw tight.

  IMPORTANT SAFETY INFORMATION

  Not modify wheel spacer and remove factory installed studs on wheel spacer/adapter.

  Not use multiple spacer over a single wheel.

  

  ---