Fit For: - 2003 - 2006 FORD EXPEDITION All Models
- 2005 - 2006 LINCOLN NAVIGATOR All Models
Package Includes: - 1x Front Lower Right Control Arm + Ball Joint - K80710
- 1x Front Lower Left Control Arm + Ball Joint - K80711
Fault judgment: 2Pcs Front Lower Control Arms Kit For 2003-2006 Ford Expedition 4-Door 5.4L V8
Fit For:
- 2003 - 2006 FORD EXPEDITION All Models
- 2005 - 2006 LINCOLN NAVIGATOR All Models
Package Includes:
- 1x Front Lower Right Control Arm + Ball Joint - K80710
- 1x Front Lower Left Control Arm + Ball Joint - K80711
Fault judgment:
- When encountering a limp road, the vibration is strong, and it is shaking up and down, and the body is twisted.
- When the car is driving, every time it vibrates up and down, the suspension device makes a "guckling" noise
- If there is a problem with the front wheel suspension system, the direction will deviate to one side, and continuous correction is required to maintain normal driving.
A normal shock absorber will generate heat when it is working. If it does not generate heat or if oil leaks from the shock absorber, it means that the shock absorber has been damaged. During the inspection, the condition of the shock absorber rubber sleeve should also be checked. If it is found to be damaged, it should be replaced together with the shock absorber in time. In addition, it may be that the fastening bolts are loose.
Know how to replace the ball joint:
Engage the parking brake. Set the parking brake on the vehicle and set the wheel block on one of the tires you will not remove. After the tire screws are loosened, jack up the jack.At this time, completely remove the wheel nut, and then remove the tire from the vehicle.
- step 2: Removing the Old Ball Joint
- Pop loose the ball joint. You will most likely need to use a hammer and a special tool called a “pickle fork” or tie rod separator to get enough leverage to maneuver.
- With the wrench, remove the largest nut from the joint, replace with the new nut, and then drive the pickle fork between the control arm and the steering knuckle. And before hammering away,you will need to put the castellated nut on.
- Remove the allen bolts and slide the control arm free. Loosen bolts or drill out rivets holding the ball joint in place, and slide out the ball joint.
- step 3: Installing the New Joint
- Guide the new joint through the knuckle hole. Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from.
- Bolt the joint into place using the hardware included.
- Torque the bolts to the proper specifications.Generally, the specs will be about 44 pounds per foot on the screws and around 80 for other bolts. Always defer to the owner's manual for accurate numbers, however.
- Screw in the new grease fitting and pump grease into the assembly.
Notes:
- Please be sure to check carefully whether the part is suitable for your car model before placing an order.
- If you have any questions after receiving the goods, please contact us in time, we will give you a satisfactory answer.
Item SpecificsBrand everpartstorecsPlacement on Vehicle Left Right Front LowerManufacturer Part Number 10407637Interchange Part Number K80710 K80711OE/OEM Part Number Front Driver and Passenger Side ReplacementVintage Car Part NoType Control Arm & Ball Joint AssemblyManufacturer Warranty 1 YearMaterial Alloy SteelItems Included Mounting HardwareMounting Style Bolt-OnUniversal Fitment NoCotter Pin Hole YesAdjustable YesModified Item NoCustom Bundle YesOE Spec or Performance/Custom OE SpecControl Arm Construction ForgedFeatures GreasableKit or Single Part KitKit Included 2 PiecesFinish CoatedSurface Finish Premium QualityPartlink Number For Ford Expedition Lincoln NavigatorStore Speciality Suspension & SteeringSuspension Grade StandardBundle Description 1x Right 1x Left Lower Front Control Arm and Ball Joint AssemblyCross Part Number 2003 2004 2005 2006Cross Reference Part Number 4553923, 455339225,488264, 4882285
Shipping
tellusthenewaddresswithin 12 hoursafterpayment
(nodeliverytoremoteareas).
PayPal preferred.
Other payments accepted by also can be accepted.
Service
within30days.
Do check the compatible chart or contact us if you have any quetion in compatibilities before ordering the items.
STORE HOMEHOT SELLINGCOOL SUMMERSENSORSEXTERIOR Shop CategoryStore Home lift support Condenser Air Diesel Heater Blower Resistor Blower Motor Heater Core Suspension Kits Thermostat Housing ABS Wheel Speed Sensor Window Switch Oxygen Sensor 3Rd Brake Light Mass air flow sensor AC Compressor Cooling Fan Towing Mirrors Door Handle Roof Rack Radiator Sensor Knock Sensor Catalytic Converter Window Regulator Wheel Spacers Alternator Other
2Pcs Front Lower Control Arms Kit For 2003-2006 Ford Expedition 4-Door 5.4L V8
Fit For:
- 2003 - 2006 FORD EXPEDITION All Models
- 2005 - 2006 LINCOLN NAVIGATOR All Models
Package Includes:
- 1x Front Lower Right Control Arm + Ball Joint - K80710
- 1x Front Lower Left Control Arm + Ball Joint - K80711
Fault judgment:
- When encountering a limp road, the vibration is strong, and it is shaking up and down, and the body is twisted.
- When the car is driving, every time it vibrates up and down, the suspension device makes a "guckling" noise
- If there is a problem with the front wheel suspension system, the direction will deviate to one side, and continuous correction is required to maintain normal driving.
A normal shock absorber will generate heat when it is working. If it does not generate heat or if oil leaks from the shock absorber, it means that the shock absorber has been damaged. During the inspection, the condition of the shock absorber rubber sleeve should also be checked. If it is found to be damaged, it should be replaced together with the shock absorber in time. In addition, it may be that the fastening bolts are loose.
Know how to replace the ball joint:
Engage the parking brake. Set the parking brake on the vehicle and set the wheel block on one of the tires you will not remove. After the tire screws are loosened, jack up the jack.At this time, completely remove the wheel nut, and then remove the tire from the vehicle.
- step 2: Removing the Old Ball Joint
- Pop loose the ball joint. You will most likely need to use a hammer and a special tool called a “pickle fork” or tie rod separator to get enough leverage to maneuver.
- With the wrench, remove the largest nut from the joint, replace with the new nut, and then drive the pickle fork between the control arm and the steering knuckle. And before hammering away,you will need to put the castellated nut on.
- Remove the allen bolts and slide the control arm free. Loosen bolts or drill out rivets holding the ball joint in place, and slide out the ball joint.
- step 3: Installing the New Joint
- Guide the new joint through the knuckle hole. Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from.
- Bolt the joint into place using the hardware included.
- Torque the bolts to the proper specifications.Generally, the specs will be about 44 pounds per foot on the screws and around 80 for other bolts. Always defer to the owner's manual for accurate numbers, however.
- Screw in the new grease fitting and pump grease into the assembly.
Notes:
- Please be sure to check carefully whether the part is suitable for your car model before placing an order.
- If you have any questions after receiving the goods, please contact us in time, we will give you a satisfactory answer.
ShippingPaymentServiceNote
tellusthenewaddresswithin 12 hoursafterpayment
(nodeliverytoremoteareas).
PayPal preferred.
Other payments accepted by also can be accepted.
within30days.
Do check the compatible chart or contact us if you have any quetion in compatibilities before ordering the items.
